Premixed 10 to 30 mm thick cementitious screed.
Vetotop CS535 is a single component cementitious floor screed composed of hydraulic binders, silica sand, selected aggregates special additives and fibers. It is supplied as a dry powder in pre-weighed bags ready to use on site, once mixed it will form a trowellable mortar that is applied in thicknesses between 10 and 30 mm.
Vetotop CS535 supplied in 50 Kg Bag. Yield - 23.3 - 32.3 Ltr
Original sealed bag of Vetotop CS535 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC
For the preparation of mixture, pour into a container 6.5-8 liters of water for 50 Kg bag of Vetotop CS535.
Add the powder to the water and mix with a low speed electric drill fitted with a suitable paddle, until a uniform, lump free consistency mix is achieved. No further water should be added to the mix. Do not add water to the mix once its start to set.
Add the required aggregate type to the mixed screed slowly while continuing mixing until a uniform consistency as achieved.
Pour the mixed product onto the surface and spread to the desired thickness using steel trowel or suitable tools.
Cure the screed as per standard concrete curing practices. Do not subject the screed to vehicular traffic for 28 days till ensure full cure and systems ability to withstand designed traffic loads.
A concrete sealer is required for enhancing the screed durability and resistance to ingress of water, apply Vetoseal XW770 at a rate of 8 to 12 m2 per liter. Make sure that the sealer is uniformly applied and covering all screed surface.
Clean tools with water promptly before material hardens. Hardened material can be mechanically removed.
The surface should be sound, clean, free from loose material, grease, laitence, dirt curing compound, etc.
Vetotop CS535 can be laid as a bonded screed by applying Vetobond PB434 slurry to prepared concrete substrate as a bonding and priming layer, alternatively and epoxy bonding agent can be used such as Vetobond EB430 or EB431.
To prepare the slurry primer mix 1 volume of VetoBond PB434 to 1 volume of clean water with 3 volumes of fresh cement and mix until a smooth consistency is prepared. Scrub the mixed slurry into the concrete surface, while the slurry is wet apply Vetotop CS535 in order to insure good adhesion with the substrate.
Vetotop CS535 is highly alkaline therefore avoid direct contact with eyes or skin. Vetobond PB434 is latex emulsion. It is recommended to use protective gloves and goggles during application.
Any skin contact should be washed with plenty amount of water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.
Vetotop CS535 is non-flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Non-metallic emery based dryshake monolithic floor hardener
Premixed 2 to 10 mm thick cementitious self leveling underlayment
Premixed 30 to 100 mm thick cementitious screed.
Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating
Solvent based high performance, self priming, thin epoxy topping
High performance aliphatic acrylic protective & decorative coating for concrete and masonry