Concrete Grouts Repair and Enhancement
Vetorel XT429

Powder release agent for decorative and stamped concrete.

Uses
Releasing of stamping and imprinting tools from concrete surfaces.
Act as a secondary colorant and antique effect producion of imprinted concrete.
Fast Download
Technical Data Sheet
download (*.pdf 0.20Mb)
Technical Information
Product Description

Powdered Release Agent is a ready to use colored powder, streak free and powder formulated to be easily applied onto the surface of colored or plain concrete. Vetorel XT429 Release Agent is broadcast over the surface of freshly placed colored-concrete floors before imprinting with stamps or other texturing tools or rollers. It forms a bond-breaking barrier that helps prevent the tools from sticking to the fresh concrete.
Color Release Agent is used in conjunction with Vetotop XT537 colored hardener.

Advantages
  • Releases stamping mould from concrete surface
  • Water Resistant.
  • Excellent bond breaking properties.
  • Create two-toned effect.
  • Streak free.
  • Fade resistant.
  • Easy to use single component powder.
  • Wide color range availability.
Packaging & Coverage

Vetorel XT429 is supplied in 17.5 Kg bag, with coverage 100 m2 / Bag

Shelf life & Storage

Original sealed container of Vetorel XT429 and has a shelf life of 24 months provided it is stored clear of ground in a dry shaded place below 35ºC.

Application Information
Instructions for use

Application


Color Release Agent is specially formulated for use with stamped concrete. We recommend to use it with recommended Vetonit Color Hardener and Sealers.
Sub-base must be graded to ensure an even thickness of concrete. At the time of concrete placement, the sub-base must be moist but with no standing water, well consolidated and frost-free. If necessary, the sub-base should be dampened with water in advance of concreting to avoid uneven suction and premature drying out of the underside of the slab.

Immediately prior to imprinting, the Release Agent should be hand-broadcasted evenly across the surface by the dry-shake method, normally in one broadcasting operation. Now imprinting is possible. After the concrete has achieved initial set, the release agent may be removed by pressure rinsing with a high power pressure cleaner.

Sealing

Vetonit recommend allowing concrete to cure for minimum 7 days before cleaning and sealing.
Consult Saveto technical department for any additional information.

Cleaning and disposal


Clean all tools and equipment with water.
The disposal of excess or waste material should be carried out in accordance with local legislation under the guidance of the local waste regulatory authority.

Additional Information
Health & Sefety

Do not breathe dust. Do not ingest. Keep out of the reach of children. Use with adequate ventilation. A dust mask (niosh/msha tc 21c approved), safety goggles, and gloves should always be used. Silica based products present health hazards. May cause delayed lung injury (silicosis). First aid: eyes - do not rub eyes. Immediately flush thoroughly with plenty of water. Skin - wash thoroughly with soap and water. Remove soiled clothing. Inhalation - move to fresh air. If symptoms persist or develop, or if ingested, get medical attention. Wash thoroughly immediately after handling. Replace inner bag and close container after each use.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor EG346

Epoxy resin twin cartridge anchoring grout

Vetoanchor PG347

Polyester injection and anchoring grout

Vetocure XT425

Water based concrete curing compound

Vetocure XT426

Resinous, render receiving concrete curing compound

Vetocure XT427

Water based acrylic curing compound and primer

view more
Featured Product
Pool GROUT

Water resistant grout for swimming pool tile joints

Uses
Grouting of walls and floors joints subjected to varying range of dry or humid conditions
Pool Grout is specifically designed to be compatible with Saveto Pool Fix product used for laying & fixing tiles
Suitable for use with both ceramic and marble tiles
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map