Specialty polymer modified cementitious adhesive for glass blocks and glass mosaic tiles.
Vetoset CA544 is a special mortar composed of high performance hydraulic binders, synthetic resins, carefully selected fillers and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site which only require the addition of clean water to produce a creamy paste with thixotropic properties. Vetoset CA544 is specially formulated for sealing glass blocks and installation of glass tiles. Vetoset CA544 does not contain asbestos fibre or other toxic materials.
Single component, it requires only addition of water, easy to mix & apply.
Excellent physical & mechanical properties.
Extended open time, adjustability time, making installation easier.
Excellent resistance to yellowing.
Suitable for interior & exterior applications.
Excellent resistance to staining.
BS:EN 12004 as type C2TE S1.
ISO 13007 as type C2TE S1.
ASTM C348 & C349
Vetoset CA544 is supplied in 20kg Bags, Yield: 16 Liters
Original sealed container of Vetoset CA544 has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.
For the preparation of mortar adhesive, pour into a container 5.6- 6.4 liters of water for each 20 Kg bag of Vetoset CA544. Add the powder to the water and mix with a low speed electric drill fitted with a suitable paddle for 4-5 minutes, until a uniform, lump-free consistency is achieved. Allow the mixed material to stand for about 10 minutes and remix briefly with no further water to be added.
It can also be blended manually for small quantity but ensure correct amount of powder to water is maintained.
Mixed material can be used within 60 minutes at 25 degrees C.
Do not try to remix or add water to the mixture once the mortar adhesive starts to harden. If the material starts to harden.
Apply Vetoset CA544 with a trowel, then position the glass blocks in the opening. Use special molder to verify the glass block alignment. Remove the excess of mortar before it hardens.
For Gap filling, compact the product using a smooth rubber spatula. Let the product harden for about 10 minutes, after that clean the surface using a damp sponge. When the product is well hardened, clean it with a dry rag.
Tools and equipment can be cleaned with water immediately after use. Hardened materials will require removal by mechanical means.
The surface should be sound, clean free from loose material etc. Horizontal surfaces must be leveled and vertical sides should be perfectly plumb-in or secured in order to guarantee a perfect alignment of glass blocks. The support must be solid, compact, free from loose parts, dust and greasy substances.
Vetoset CA544 is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.
Vetoset CA544 is non-flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Weather resistant cementitious adhesive for ceramic tiles.
Polymer modified water resistant adhesive for fixing swimming pools, fountains & watertanks tiles.
Water resistant grout for swimming pool tile joints.
Polymer modified weather resistant adhesive for porcelain tiles.
High quality ceramic tile adhesive for projects.
Acrylic polymer modified decorative finish coat applied at thicknesses from 3 to 20 mm