Plasters & Masonry
Spatter Dash S

Weather resistant premixed cementitious scratch coat

Internal & external in wet & dry conditions.
On block walls, fair-faced concrete and precast panels prior to plastering application.
Plaster bond enhancer and mechanical key on horizontal, vertical and overhead application.
Enhances the binding between substrate & plasters or coatings.
Fast Download
Technical Data Sheet
download (*.pdf 0.55Mb)
Method of Statement
download (*.pdf 0.21Mb)
Technical Information
Product Description

Spatter Dash S is a cement based key coat composed of hydraulic binders, selected sand aggregates and high performance additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce easily spray-able mortar. Spatter Dash S is a high quality product for multipurpose applications and does not contain additional bonding agent.
Spatter Dash S is available in grey colour.

  • Factory controlled pre-blend ensures consistent high quality.
  • Requires only addition of water on-site at the time of usage.
  • Manual or spray machine application or by hawk & trowel techniques.
  • Superior workability.
  • Easy application with uniform work flow enables high productivity & superior finishing.
  • Good adhesion on variety of substrates.
  • Internal & external applications.
  • Weather resistant.
  • Suitable for humid & dry conditions.
  • Suitable for vertical & ceiling surfaces.
Compiliance Standard
  • BS:EN 998-1:2003
  • ASTM C348, C897
  • ASTM C926 C349
  • Cement type: ASTM C150, type1
Packaging & Coverage

Spatter Dash S is supplied in 50kg Bags, with coverage: 1.3-1.6 Kg / m2 / mm thickness

Shelf Life & Storage

Original sealed container of Spatter Dash S has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Spatter Dash S is available in grey colour.
Application Information
Instructions for use

Add to the mixing container 10-12.5 litres of water foreach 50 Kg bag of Spatter Dash S. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when homogenous mix is achieved.

Smooth Concrete Surfaces
For extra adhesion requirment, add 1 litre of Vetonit Bond 2 to the mixing water and adjust the water requirement accordingly for each 50 kg bag. Follow same mixing procedure as described above.
Mixed material can be used within 1 hour.
Do not add water to the mix once the mixed mortar start to harden.

Spatter Dash S preferably be applied in a single coat application to achieved desired thickness of 4-6 mm. Apply mixed material using mechanical spray or manual spatter machine or hawk & trowel technique.Cover 95-100% of surface area to be plastered. Allow the installed application to remain undisturbed for at least 48 hours.

Spatter Dash S is best cured by spraying water on the surfaces of applied materials every 12 hrs for minimum of 3 days. During hot & dry conditions allow curing for minimum of 5 days. It will help to obtain high mechanical strengths and minimize the risk of surface cracks.

Surface Preparation

Substrate  should  be  sound,  clean,  free  from  loose material, grease, laitance, dirt curing compound, etc.Prior to Spatter Dash S application, wet the entire surfaces with clean potable water and surface should look damp at the time of Spatter Dash S application.

  • Do not mix with any additives or products, unless recommended by Saveto.
  • Make sure the substrate is suitable for plaster coat application. In case of doubt, try on sample area to assess its suitability.
  • Do not apply the product at temperature less than +5ºC. During summer season the working area must be covered to prevent ill-effects from direct sun and also excessive air-draught during initial curing stage.
  • Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically only.
  • Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically.
Additional Information
Health & Sefety

Spatter Dash S is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.
Spatter Dash S is non-flammable.
For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Acoustic PLASTER

High quality light weight premixed acoustic plaster

Cool Mortar

Advanced modified cementitious light weight, thermal insulating masonry mortar

Masonry Grout Filler

Premixed cementitious masonry grout

Plaster Gypsum

High quality light weight gypsum plaster

Plaster Gypsum PERLITE

Thermal insulation llight weight gypsum perlite plaster

view more
Featured Product
Vetotouch Repara

Dual component cementitious coating and color nuetralizer for cementitious decorative finishes

Water absorption reduction and resistance to atmospheric contaminants.
As a color uniforming coat for the Vetotouch product range..
Patch cosmetic repairs of thin cementitious finishes.
Colored coating for fair-faced concrete providing carbonation resistance while being breathable.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map