Epoxy resin twin cartridge anchoring grout
Vetoanchor EG346 is a two-component, styrene free, pure epoxy-based, high strength adhesive anchoring system. The system includes injection adhesive in plastic cartridges, mixing nozzles, dispensing tools and hole cleaning equipment. The product is designed for bonding threaded rod and reinforcing bar hardware into drilled holes in the concrete base and solid masonry materials. Vetoanchor EG346 is available in two packaging twin cartridge system: 400 milliliter that is side by side cartridges requiring a specifically designed injection gun.
Vetoanchor EG346 is supplied in 400 ml twin cartridge sets
Original sealed kits of Vetoanchor EG346 has a shelf life of 18 months provided it is stored clear of ground in a dry and shaded temperature controlled place <35ºC.
The high strength of the cured resin permits strong anchors to be created. Ultimate strength is varied by:
- Strength of host material.
- Length of resin bond to bar.
- Hole preparation and formation.
- Type and dimension of the bar.
Refer to Vetoanchor EG346 for more details and information.
Open the cartridge and remove the red stopper on top. Use Good nozzles after removing the red stopper from the cartridge, and attach the mixing nozzles screwing down tightly. Assemble cartridge into the caulking gun and dispense 2-3 trigger pulls of adhesive to waste until Grey color appears with no streaks.
Open the valve and squeeze the handle so the material is dispensed out of the nozzle until an even, uniform grey color is achieved. Before a new cartridge is introduced into the hole, dispense the first 10 ml or so to waste until mix is even on color (Orange) as well. Initial flow should be disposed of into an empty packaging or similar materials. Inject resin into the hole, starting from the bottom of the hole. The material must be injected without creating air pockets.
Insert studs or anchors, by pushing the stud into the hole using a slow twisting motion. Wipe away the excess material. Anchor or stud needs to be clean and oil-free. Do not touch studs or anchor until the mixture gels. Do not load the anchor until curing is completed as per curing time table.
Optimum performance of Vetoanchor EG346 grouts requires rough sided, dust-free holes. Use of rotary percussive drills with air pressure is recommended.
Diamond drilled holes should be under-reamed.
Cast holes should preferably be inverse dovetail configuration. If parallel-sided holes are cast they should be rough to provide adequate keying.
Brushing the holes and air blowing is a must for all holes, the concrete needs to be dry with a relative humidity of less than 75% prior to application.
Do not install anchors when the substrate temperature is less than 0°C.
Do not install anchors when Vetoanchor EG346 temperature is less than 15°C.
AT temperatures below 15°C the product should be warmed or stored in temperatures of 15-30°C for 24 hours prior to use to improve product flow and cure.
If the gelling time is superseded, use a new static mixer.
Do not cut or shorten nozzles.
If the cartridge is not finished, clean the opening, then put the plug back and cap tightly. The cartridge set can be used again by replacing the static mixer.
Do not dilute the material with any solvents and/or other chemicals.
Not suitable for use in diamond cored holes without roughening.
Please ensure spiral mixer in nozzles.
Do not install into uncured concrete.
Use Good Use nozzles, other nozzles may cause ineffective mixing and adversely affect the material.
Contact with the skin should be avoided as certain sensitive skins may be affected if contacted with epoxy resin. In case of contact with resin, the skin should be washed immediately with soap and water - do not use solvent.
When handling these products, wear gloves and use barrier creams.
Eye contamination must be immediately washed with plenty of water and medical treatment sought.
Vetoanchor EG346 is not Flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Polyester injection and anchoring grout
Water based concrete curing compound
Multi-Purpose Acrylic Resin Curing Compound
Water based acrylic curing compound and primer *
Multipurpose universal cementitious non-shrink grout
Twin Pack Putty Formulated for Thick Vertical and Overhead Applications