Jordan
Bahrain Egypt Saudi Arabia UAE
EN
EN
Contact news and events About us Home
PRODUCT RANGE
SYSTEM
Selector REFERENCES DOWNLOAD SECTION
Primers and Ancillary
Ready Mix Bond

Multi-purpose bonding agent & admixture

Uses
Works as admixture with plaster, lime/sand cement screeds, renders, mortars and cement grouts.
Works as bonding agent and can be sprayed or brushed on green substrates to improve bonding of plasters, patching compounds. Renders, mortars, joint tape fixing etc.
Ready Mix Bond can be used for both for internal and external applications.
Fast Download
Technical Data Sheet
download (*.pdf 0.14Mb)
MSDS
download (*.pdf 0.21Mb)
Technical Information
Product Description

Ready Mix Bond  is a single component acrylic based, bonding agent for cementitious materials. It is a water based, specially formulated to enhance bonding properties as well as improve mechanical strengths of plaster mixes when incorporated with mixing water. Ready Mix Bond also reduces shrinkage cracks during early stages of cement hardening by minimizing surface water loss in fresh applied mixes. Ready Mix Bond is ideal for use with variety of sand/ cement based mixes. Ready Mix Bond can be diluted on site with potable water for desired applications.

Advantages
  • Multipurpose usage.
  • Can be used as bonding agent & admixture.
  • Enhances bonding of plaster, sand/cement screed, renders etc.
  • Improves hydration & curing when added to cement based mixes.
  • Improves compression strength & abrasion.
  • It adheres well to various construction materials, including concrete, stone, etc.
  • Ensure brighter & long lasting colour to architectural finishes.
  • Reduces shrinkage & cracks.
Compiliance Standard
  • ASTM C932
  • BS 6319
Packaging & Coverage

Ready Mix Bond is supplied in 20 liters Containers, Coverage: 8 -10 m²/Ltr as bonding agent

Shelf Life & Storage

Original sealed container of Ready Mix Bond has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.
Ready Mix Bond is non-flammable.

Colors
Milky white liquid
Application Information
Instructions for use

Application
Ready Mix Bond has tendency of soft settlement on storage and therefore it is recommended to mix the material in same container prior to use.
Follow the dilution ratio required for each type of premixed mortar.

As Admixture
Add 3 parts of Ready Mix Bond with 1 part of water. Mix thoroughly to obtain uniform consistency liquid. Add the diluted Ready Mix Bond to pre-blended sand/cement plaster, mortar, or other dry mixes. Mix for 3-4 minutes using mechanical mixer at low speed.
Let the mixture stand for 10 min and mix again briefly to achieve homogeneous lump free mixture.

As Bonding Agent
As a bonding agent, Ready Mix Bond is used without dilution. Apply Ready Mix Bond using brush or spray directly onto substrate. If using hand pump, spray at a rate of 8-10 m2/litre.
immediately, while bonding agent is still wet follow by applying plaster, render, mortars or joint tapes etc.

Note: Ready Mix Bond should remain tacky when applying top coat finishes.

Surface Preparation

Clean all surfaces and remove any dust, unsound material, plaster, oil, paint, grease, corrosion deposits or algae. Roughen the surfaces, remove any laitence and expose aggregate by light scabbling or grit-blasting.

Limitation
  • Use the whole material once you opened the pack, as the material start to skin & then dry. Any part material left in container must be kept air tight.
  • Do not mix with any additives or products unless recommended by saveto.
  • Tools should be cleaned with water before it hardens. After the hardening its residuals can be removed mechanically only.
  • For further information contact our technical department.
Additional Information
Health & Sefety

Ready Mix Bond is irritant and harmful therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. In case of contact with eyes, clean immediately with plenty of clean cold water and seek medical advise.
Ensure adequate ventilation when using the material and avoid inhalation of vapours.
Refer to Material Safety Data Sheet for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Saveto Bond 2

Multipurpose low viscosity bonding agent & admixture

Saveto PP Fiber

High Quality Monofilament Polypropylene Fibers

Vetobond PB436

Polymeric soil stabilizer

Vetobond PB434

Polymeric bonding agent, waterproof mix enhancer & primer

Vetobond PB433

Versatile resin adhesive, cement modifier, bonding agent & sealer

view more
Featured Product
Vetonit Ultra

Polymer modified weather resistant multipurpose adhesive for tiles.

 

Uses
For Ceramic tiles, natural stone conglomerates (Granite & Marble, Terrazo) , artificial stone and large format tiles.
Tiling on smooth concrete surfaces, lightweight bricks, blocks, plaster boards.
Tiling on wall surfaces that are plastered with water resistant plasters such as Vetonit Render & Vetonit Base WR on damp concrete interiors.
Suitable for dry & wet conditions.
Suitable for tile on existing tile applications.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map
Home
About us
news and events
Contact
DOWNLOAD SECTION
REFERENCES
Copyright ©2015-2016 Saudi Vetonit Co. Ltd. All Rights Reserved.