Waterproofing
Vetoproof AM764

Single component ultra flexible acrylic waterproofing membrane

Uses
Waterproofing of concrete, asbestos, metal,cement and gypsum board surfaces
Protecting spray-PU membranes from UV rays
As a decorative overlay on bituminous membranes and over existing terrazzo tiles
Waterproofing of corrugated sheet and sloped roofs
Fast Download
Technical Data Sheet
download (*.pdf 0.17Mb)
Method of Statement
download (*.pdf 0.20Mb)
Technical Information
Product Description

Vetoproof AM764 is a single component elastomeric water-based acrylic membrane that has versatile uses for waterproofing in residential and commercial construction. The product is available in a variety of colors that are extremely stable in extreme weather conditions. Vetoproof AM764 has high polymer content making it resistant to yellowing and color fading.

Advantages
  • Flexible elastomeric product
  • Easy to use single component
  • UV and color stable
  • Excellent weathering resistance
  • Can be applied over sloped roofs
  • Easy to maintain
  • Available in a wide range of colors
Packaging & Coverage

Vetoproof AM764 supplied in 18 Litlers Pails
Coverage - 2.4 m2 / Liter / coat

Shelf Life & Storage

Original sealed container of Vetoproof AM764 and has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 35ºC.

Colors
The product is available in a variety of colors.
Application Information
Instructions for use

Application
Vetoproof AM764 can be applied by brush, roll, or airless spray machine. Porous surfaces should primed with vetoproof AM764 primer at the rate of 5 m²/liter and allowed to dry before applying the first coat. The first coat of Vetoproof AM764 should be applied at the rate of 1.5 - 2.4 m²/Liter and allowed to cure for 4 - 12 hours depending on ambient temperature.
The second coat should be applied perpendicular to the first coat at the same rate above, and allowed to cure.
For heavy pedestrian traffic, it is recommended to use fiberglass scrim reinforcement, embedded firmly in the second coat while wet, and a third coat should be applied.

Cleaning
Vetoproof AM764 product should be removed from tools, equipment and mixers with clean water prior to the initial set. Cured material can only be removed mechanically.

Surface Preparation

All surfaces should be dry and free from contamination such as oil, grease, loose particles, decayed matter, moss algal growth, laitence, and all traces of mould release oils and curing compounds. This is best achieved by lightly grit-blasting the surface. Where moss, algae or similar growths have occurred, treatment with a proprietary biocide should be carried out after the grit-blasting process. Spalled and deeply disintegrated concrete should be removed to sound concrete and repaired with a Saveto repair system. Concrete substrates should be at least 14 days old, bituminous substrates should be 3 to 6 months old prior to overcoating with Vetoproof AM764.

Limitation

Vetoproof AM764 should not be applied at ambient temperatures below 5°C and dropping. Vetoproof AM764 should not be applied on surfaces expected to suffer form rising dampness or relative humidity greater than 75%.

Additional Information
Health & Sefety

Vetoproof AM764 contains acrylic polymer which can be harmful to the skin. During use, avoid contact with skin and eyes. Wear suitable protective clothing, gloves, eye protection and respiratory protective equipment. The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. In case of contact with eye, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately – do not induce vomiting.

Vetoproof AM764 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoproof AM763

Single component acrylic waterproofing membrane

Vetoproof CM740

Single component elastomeric crack-bridging cementitious waterproof membrane

Vetoproof CM744

Polymer modified water resistant cementitious top coat

Vetoproof CM741

Single component penetrating waterproofing system for concrete

view more
Featured Product
Vetoproof EC720

Non-toxic solvent free epoxy waterproof wall, floor & tank coating

Uses
Waterproofing of concrete, asbestos, metal, cement and gypsum board surfaces
Water tanks and reservoirs
Diesel and sewage tanks
Hospital clean rooms
Food processing areas
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map