Flooring & Coatings Systems
Vetotop EC397

Slightly Elastic Solvent free Industrial-Grade high performance, high build epoxy flooring system .

Floor coating for a variety of industrial applications such as: production assemblyareas, workshops, dairies, bottling plants, breweries, pharma plants, kitchens, showrooms, etc.
Aircraft hangers, anti-slip floors, ramps & high traffic.
Wet working areas subject to chemical spillage.
Vehicle production factories and parks.
Fast Download
Technical Data Sheet
download (*.pdf 0.14Mb)
Technical Information
Product Description

Vetotop EC397 is a two component high performance solvent free epoxy coating system that is especially designed for industrial flooring. Once cured, the product has excellent abrasion and chemical resistance. Vetotop EC397 provides an attractive hard wearing and easily cleanable floor finish. Its use on floors will enhance lighting in the environment due to the product reflective properties.


High abrasion and impact resistance.

Ease of application.

High abrasion and chemical resistance. u   Low maintenance costs.

Hygienic, impervious and easily cleanable. u   Slip-resistant finish can be obtained.

Available in 8 standard colors with possibility of custom RAL colors.

High  bond,  stronger  than  concrete  cohesive strength.

Slightly flexible to handle vibration u   Economic installation.

Compiliance Standard

BS EN476:2009 as class 1 in flame spread.

Packaging & Coverage

Vetotop EC397 supplied in 4 Liter Kit. Yield 2 m2 / Liter @ 500 microns wft.

Shelf Life & Storage

Original sealed bag of Vetotop EC397 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.

Available in 8 standard colors with possibility of custom RAL colors.
Shelf life & Storage

Original sealed bag of Vetotop EC397 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.

Application Information
Instructions for use

Usage Instructions


 Priming is not normally required provided the substrate is sound, prepared and good quality non porous concrete. However, if concrete surface is porous, or w/c ratio is >0.5 it is recommended to use Vetoprime EP390.

Vetoprime EP390 should be mixed in the proportions supplied. Add the entire contents of the hardener can to the base can. When thoroughly mixed, preferably using a slow speed mixer, the primer should be applied in a thin, continuous film using rollers or stiff brushes. Work the primer well into the surface of the concrete taking care to avoid ponding or over application. The primer should be left to achieve a tack-free condition before applying the top coat.


Mixing Vetotop EC397

 In a separate mixing vessel, use a slow speed mixer to mix the base, hardener for 3 minutes. Mix these components in the quantities supplied taking care to ensure all containers are scraped clean. Do not add solvent thinners at any time.



 The first coat of Vetotop EC397 should be laid using a short haired lamb wool roller, or gauged squeegee to achieve a continuous coating. Ensure that loose hairs on the roller are removed before use. A minimum film thickness of 500 microns per coat should be applied for flooring system (this can be increased where specifications demand).

 Vetotop EC397 should be topcoated with Vetotop UC371. The top coat can be applied in the same manner within 8 to 24 hours of the application of the top coat.


Antislip Aggregates


If the option of using antislip aggregates has been chosen, the base coat should be dressed with the chosen antislip aggregates as soon as possible after laying of the base coat. The recommended procedure is to completely blind the base coat i.e. apply excess dressing aggregate to completely obliterate the base coating.

 Alternatively, the antislip silica particles can be broadcast in a light random dressing to provide a less dense finish, or the product can be used to obtain a smooth finish by omitting the antislip aggregates.

 When the base coat has reached initial cure (after 12 hours at 20°C or 6 hours at 40°C), the excess aggregate should be vacuum cleaned from the surface.

 The top coat can now be applied by a short haired roller or airless spray equipment. Care should be taken to ensure that a continuous film is achieved and the rough surface caused by the aggregate is completely sealed. This topcoat must be applied within 36 hours at 20°C (24 hours at 40°C) of the application of the resin base coat.


Expansion Joints


Expansion  joints  in  the  existing   substrate   must be retained and continued through the Vetotop EC397 topping. Saveto have a range of joint sealants specifically designed for flooring (see Vetoflex PS781, Vetoflex PS782 and Vetoflex PS786 product data sheets).




Tools and equipment should be cleaned with Vetonit Solvent XX400 immediately after use.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitence, dirt curing compound, etc.

Laitence and weak surface layer shall be removed using mechanical methods such as grinding or blasting in order to provide a sound well profiled surface. All necessary repairs should be made prior to application by using epoxy mortar from Vetorep ER range.

New concrete floors shall be at least 28 days  old with moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).

Additional Information
Health & Sefety

vetotop EC397, Vetotop UC371, Vetoprime  EP390 and Vetonit Solvent XX400 should not come into contact with skin and eyes or be swallowed. Ensure adequate ventilation and avoid inhalation of vapors. Some people are sensitive to resins, hardeners and solvents. Wear suitable protective clothing, gloves, and eye protection. If working in confined areas, suitable respiratory protective equipment must be used.

The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medial advice. If swallowed, seek medical attention immediately - Do not induce vomiting.

Vetoprime EP390 and Vetonit Solvent XX400 are flammable. Keep away from sources of ignition. No Smoking. In the event of fire extinguish with CO2 or foam.

Important note

Saveto manufactures a wide range of construction chemicals and specialty products for various applications divided into the following product groups:

Concrete Repair, Grouts and Enhancement. u   Wall & Facade Systems.

Flooring and Coating Systems.

Sealants and Joints.

Plasters & Renders.

Puties & Finishes

iling Systems


Primers & Ancillary Products.

Specialty Products.

Saveto also provides various technical information such as CAD details, detailed method statements, specification clauses, application manuals, product selectors and technical support both in contractors and consultants offices as well as construction sites.

More Products from this section
Vetotop XT539

Non-metallic emery based dryshake monolithic floor hardener

Vetotop CL530

Premixed 2 to 10 mm thick cementitious self leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed.

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed.

Vetotop EC198

Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating

view more
Featured Product
Vetotop EL499

Self smoothening epoxy based floor topping from 2 to 4 mm thickness

Industrial kitchens and food processing plants
Vehicle factories and car parks
Clean rooms and laboratories
Heavy duty applications, turbine rooms, armories and hangers
Any flooring were impact resistant
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map