Tile Adhesives and Grouts
Vetoset CA546

Cementitious tile adhesive for fixing marble & mosaic tiles.

 

Uses
• Specifically designed for marble and natural stone conglomerates.
• Suitable for large format tiles
• As a thin bed tile fixing mortar for all types of ceramic tiles, marbles, terrazzo tiles.
• Tiling on normal & smooth concrete surfaces, Plasters, bricks, and blocks, glazed & non- glazed marbles and mosaic tiles.
• Suitable for dry & wet conditions.
Fast Download
Technical Data Sheet
download (*.pdf 0.12Mb)
Technical Information
Product Description

Vetoset CA546 is a weather resistant cement based adhesive mortar composed of waterproof polymer, hydraulic binders, selected aggregates, and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which required only addition of clean water to produce easily workable adhesive. Vetoset CA546 is suitable for internal & external use. Vetoset CA546 is generally applied at thicknesses from 3 mm to 10 mm.

Advantages
  • Factory controlled pre-blend ensures consistent high
  • Requires only addition of water on-site at the time of
  • Easy tile installation that enables high Productivity.
  • Superior workability.
  • Suitable in dry & humid conditions.
  • High bond adhesion on variety of tiles available in the local market.
  • Internal & External use.
  • Suitable for horizontal & vertical surfaces.
  • Enhanced mechanical strength.
Compiliance Standard
  • BS:EN 12004 as C2T
  • ISO 13007
  • ASTM C348 & C349
Packaging & Coverage

Vetoset CA546 supplied in 20 Kg Bag, Coverage: 5.5-6.5m²/20kg bag

Shelf Life & Storage

Original sealed container of Vetoset CA546 has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Colors
White
Shelf life & Storage

Original sealed container of Vetoset CA546 has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Application Information
Instructions for use

Mixing

For the preparation of mortar adhesive, pour into a container 6.0-6.5 liters of water for each 20 Kg bag of Vetoset CA546. Add the powder to the water and mix with a low speed (200-300 rpm) electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.

Allow the mixed material to stand for about 10 minutes and briefly remix with no extra water added.

Application

Spread and firmly pressed the mixed Vetoset CA546 on the substrate to a uniform thickness using a notched trowel. The adhesive mortar to be spread corresponding to an area that can be tiled in 10 minutes.

Place the tiles onto the fresh adhesive mortar with a firm pressure & slight twisting to ensure a good contact of the adhesive and knocked into position.

For best results the position of the tiles should be adjusted within 10 minutes after installation.

The adhesive mortar must not rise higher in the joint than halfway the thickness of tiles.

Remove excess adhesive with a damp cloth before it dries. Joints grouting between tiles may be commenced after 24 hours for walls and 48 hours for floors using Vetonit Tile Grout.

Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically only.

Cleaning

Tools and equipment can be cleaned with water immediately after use. Hardened materials will require removal by mechanical means.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt, curing compound, etc.

Wet the all surfaces with clean water prior to the application of Vetoset CA546. Surface should appear damp with no water pooling.

Additional Information
Health & Sefety

Vetoset CA546 is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.

Vetoset CA546 is non-flammable.

Important note

Saveto manufactures a wide range of construction chemicals and specialty products for various applications divided into the following product groups:

Concrete Repair, Grouts and Enhancement.

Wall & Facade Systems.

Flooring and Coating Systems.

Sealants and Joints.

Plasters & Renders.

Putties & Finishes.

Tiling Systems

Waterproofing.

Primers & Ancillary Products.

Specialty Products.

Saveto also provides various technical information such as CAD details, detailed method statements, specification clauses, application manuals, product selectors and technical support both in contractors and consultants offices as well as construction sites.

More Products from this section
Ceramic TILE FIX

Weather resistant cementitious adhesive for ceramic tiles

 

Pool FIX

Polymer modified water resistant adhesive for fixing swimming pools, fountains & watertanks tiles.

Pool GROUT

Water resistant grout for swimming pool tile joints

 

Porcelain TILE FIX

Polymer modified weather resistant adhesive for porcelain tiles

 

PREMIUM PROJECT FIX

High quality ceramic tile adhesive for projects.

view more
Featured Product
Vetotouch Repara

Dual component cementitious coating and color nuetralizer for cementitious decorative finishes

Uses
Water absorption reduction and resistance to atmospheric contaminants.
As a color uniforming coat for the Vetotouch product range..
Patch cosmetic repairs of thin cementitious finishes.
Colored coating for fair-faced concrete providing carbonation resistance while being breathable.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map