Waterproofing
Vetoproof EC761

Solvent free coal tar epoxy based protective coating

Uses
Protection of Seawater tanks, channels and intakes
Pipe and manhole lining
Sewage works and effluent plants
Foundation waterproofing, Jetties, piers and docks
Fast Download
Technical Data Sheet
download (*.pdf 0.28Mb)
Method of Statement
download (*.pdf 0.59Mb)
Technical Information
Product Description

Vetoproof EC761 is a two component solvent free tar extended epoxy coating system that adheres perfectly to concrete and metal substrates. Once cured, the product has excellent abrasion and chemical resistance. Vetoproof EC761 provides a hard wearing and easily cleanable protective coating. Its use on floors, walls, structural elements and tanks to protect against ingress of contaminants.

Advantages
  • Versatile use
  • Does not support algae or bacterial growth
  • Excellent chemical resistance
  • Enhances structural life expectancy
  • Primerless
  • Damp tolerant and can be applied on green concrete, will double as a curing compound
  • Protects reinforcement steel and metal substrates against corrosion
Packaging & Coverage

Vetoproof EC761 supplied in 15 Liter Kit
Yield - 5 m²/liter / coat @ 200 microns

Shelf Life & Storage

Original sealed kits of Vetoproof EC761 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.

Application Information
Instructions for use

Mixing

The individual components of Vetoproof EC761 should be thoroughly stirred before the two are mixed together. The entire contents of the hardener container should be poured into the base container and the materials mixed thoroughly for at least 3 minutes. The use of a heavy-duty slow speed, flameproof or air driven drillfi tted with a mixing paddle is desirable.

Application

The mixed Vetoproof EC761 should be applied to the prepared surface using a brush or lambs-wool roller. Ensure that the area is completely coated.

Curing

The applied shall be allowed to cure for 7 days to achieve full cure to receive its chemical resistance properties.

Cleaning

Vetoproof EC761 should be removed from tools and equipment with Vetonit Solvent 1 immediately after use. Hardened material can only be removed mechanically.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitence, dirt curing compound, etc.

Laitence and weak surface layer shall be removed using mechanical methods such as grinding or blasting in order to provide a sound well profi led surface. All necessary repairs should be made prior to application by using epoxy mortar from Vetorep ER range. Pin holes, blow holes and minor irregularities can be leveled and filled by Vetorep ER350.

New concrete fl oors shall be at least 28 days old with moisture content of less than 5% (shall earlier application be required testing of substrate for
moisture conditions shall be made).

Steel substrates should be grit blasted to surface quality SA2½ (BS 4232:Second Quality) and application shall take place within 2 to 4 hours after blasting.

Additional Information
Health & Sefety

Vetoproof EC761 and Vetonit Solvent 1 should not come into contact with skin and eyes or be swallowed. Ensure adequate ventilation and avoid inhalation of vapors. Some people are sensitive to resins, hardeners and solvents. Wear suitable protective clothing, gloves, and eye protection. If working in confined areas, suitable respiratory protective equipment must be used. The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medial advice. If swallowed, seek medical attention immediately - Do not induce vomiting.

Vetoproof EC761 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoproof AM763

Single component acrylic waterproofing membrane

Vetoproof CM740

Single component elastomeric crack-bridging cementitious waterproof membrane

Vetoproof AM764

Single component ultra flexible acrylic waterproofing membrane

Vetoproof CM744

Polymer modified water resistant cementitious top coat

Vetoproof CM741

Single component penetrating waterproofing system for concrete

view more
Featured Product
Vetograin Range

Silica hardwearing aggregates to be used in conjunction of Saveto Anti-slip flooring system

Uses
Workshops, garages, power stations and loading bays.
Heavy duty factories, car park decks and aircraft hangers.
Any flooring were impact resistance is of importance.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map