Jordan
Bahrain Egypt Saudi Arabia UAE
EN
EN
Contact news and events About us Home
PRODUCT RANGE
SYSTEM
Selector REFERENCES DOWNLOAD SECTION
Plasters & Masonry
Spatter Dash SB

Cementitious Scratch / Key Coat

Uses
Internal & external scratch coat for plasters
On block walls, fairfaced concrete and precast panels prior to plastering application
Plaster bond enhancer and mechanical key on horizontal, vertical and overhead application
Fast Download
Technical Data Sheet
download (*.pdf 0.68Mb)
Method of Statement
download (*.pdf 0.21Mb)
MSDS
download (*.pdf 0.21Mb)
Catalogues
Plastering Systems Technical Guide
download (*.pdf 9.93Mb)
reference projects
Project:
Baha University, Faculty of Engineering
Location:
Saudi Arabia
Description:
Faculty of Engineering
Contractor:
Bin Jarallah Group
Consultant:
Zuhair Fayez
Technical Information
Product Description

Spatter Dash SB cement based key coat composed of hydraulic binders, selected sand aggregates and high performance additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce easily spray-able mortar. Spatter Dash SB is a high quality product for multipurpose applications and contains special bonding agent.

Advantages
  • Factory controlled pre-blend ensures consistent high qualit
  • Requires only addition of water on-site at the time of usage
  • Manual or spray machine application or by hawk & trowel techniques
  • Superior workability
  • Excellent adhesion on variety of substrates
  • Internal & external applications
  • Suitable for humid & dry conditions
  • Suitable for vertical & ceiling surfaces
Compiliance Standard
  • BS:EN 998-1:2003
  • ASTM C926
  • Cement type: ASTM C150, type1
Packaging & Coverage

Spatter Dash SB stored in 50 Kg Bag. Yield - 1.3-1.6 Kg / m2/ mm thickness.

Shelf Life & Storage

Original sealed container of Spatter Dash SB has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Colors
Grey Granular Powder
Application Information
Instructions for use

Mixing

Add to the mixing container 11.5-14.0 liters of water for each 50 Kg bag of Spatter Dash SB. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fi tted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when homogeneous mix is achieved.

Application

Spatter Dash SB preferably be applied in a single coat application to achieved desired rough thickness of 4-6 mm. Apply mixed material using mechanical spray or manual spatter machine or hawk & trowel technique. Cover 95-100% of surface area to be plastered.
Allow the installed application to remain undisturbed for at least 48 hours.

Curing

Spatter Dash SB is best cured by spraying water on the surfaces of applied materials every 12 hrs for minimum of 3 days. During hot & dry conditions allow curing for minimum of 5 days. It will help to obtain high mechanical strengths and minimize the risk of surface cracks.

Surface Preparation

Substrate should be sound, clean, free from loose material, grease, laitence, dirt curing compound, or any other substance that might impair the quality of bond with the substrate. Prior to Spatter Dash SB Application, damp the entire surfaces with clean potable water. The substrate should be neutralized  surface at the time of Spatter Dash SB application.

Limitation

Make sure the substrate is suitable for the application of Spatter Dash SB, in case of doubt, try on sample area to assess its suitability. Do not apply the product under direct rain, extreme wind, and at temperatures below +5ºC or above +45ºC.
Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically.

Additional Information
Health & Sefety

Spatter Dash SB is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap and water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.
Spatter Dash SB is non-fl ammable.
For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Acoustic Plaster

High quality light weight premixed acoustic plaster

Gypsum Plaster

High quality gypsum plaster.

Masonry Grout Filler

Premixed cementitious masonry grout

Plaster Cement Perlite

Sprayable premixed plaster

Plaster Gypsum PERLITE

Light weight gypsum perlite plaster

view more
Featured Product
Vetotop US364

High performance solvent free polyurethane screed for heavy duty applications 

Uses
Heavy duty traffic such as car parks, ramps industrial warehouses, logistical centers,...etc.
Mechanical and chemical exposure applications.
Laboratories, hospitals, food and Beverage industries.
Freezer rooms and applications where thermal shock resistance is required.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map
Home
About us
news and events
Contact
DOWNLOAD SECTION
REFERENCES
Copyright ©2015-2016 Saudi Vetonit Co. Ltd. All Rights Reserved.