Jordan
Bahrain Egypt Saudi Arabia UAE
EN
EN
Contact news and events About us Home
PRODUCT RANGE
SYSTEM
Selector REFERENCES DOWNLOAD SECTION
Sealants & Joints
Vetoflex PBR

Closed cell polyethylene backing rod

Uses
Controlling and filling gaps behind sealants
Prohibiting sealant bonding to joint fillers
Allowing joint sealant freedom of movement to achieve its desired function
Fast Download
Technical Data Sheet
download (*.pdf 0.18Mb)
Method Statement
download (*.pdf 0.21Mb)
Technical Information
Product Description

Vetoflex PBR is a closed cell polyethylene foam cord with minimal water absorption for sizing static and dynamic joints in the building industry. Available in different sizes that ranges from 6mm to 50mm in diameter and could be applied both vertically and horizontally. Vetoflex PBR serves as an excellent support for elastomeric sealants and as an efficient back up material for joint sealing applications.

Advantages
  • Easy to install (can be inserted exerting minor pressure into any kind of joint)
  • Superior resistance from deterioration
  • Exceptionally flexible
  • Non-absorbent
  • Act as bond breaker with minimum strain shape for joint sealants
  • Provides firm backing for sealant tooling
  • Withstands adverse weather conditions
  • Economical
Packaging & Coverage

Vetoflex PBR Rod Diameter

(mm)

Piece Length (m) x Pack

 

Quantity / Pack

 
6mm 100mx8pcs 800m
8mm 100mx8pcs 800m
10mm 100mx8pcs 800m
12mm 100mx8pcs 800m
15mm 60mx6pcs 360m
20mm 50mx4pcs 200m
25mm 25mx4pcs 100m
30mm 25mx4pcs 100m
40mm 4mx25pcs 100m
50mm 4mx25pcs 100m
60mm 4mx25pcs 100m
Shelf Life & Storage

Keep Vetoflex PBR stored clear of ground in a dry shaded place below 35ºC.

Application Information
Instructions for use

Application

Cut Vetoflex PBR according to the required length and lay it along the joints accordingly. Gently push the cord against the joint with extra caution not to damage the
skin of the material. Make sure that the diameter of Vetoflex PBR is approximately 20% to 25% (required depth to width ratio) greater than the width of the joint in order to ensure that the cord is tightly held in position. This procedure enhances further the aesthetic effect of the material when done on a firm base. The joint should then be sealed with a suitable sealant from Saveto’s product range.

Surface Preparation

All surfaces where the backing rod is to be inserted must be dry, smooth, clean, free from dust, laitence or loose materials. When otherwise necessary, it is highly recommended to use compressed air or a wire brush in order to remove further dirt’s, oil stains and other inconsistencies.

Additional Information
Health & Safety

Vetoflex PBR is not classified hazardous.
Vetoflex PBR is a combustible product. Avoid any exposure to all sources of ignition or flame.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoflex PU781

Multi-component polyurethane joint sealant
(Formerly known as Saveto PU2)

Vetoflex PS782

Two-component polysulphide trafficable joint sealant
(Formerly known as Saveto PS2)

Vetoflex PU780

High performance, elastomeric, single component polyurethane sealant
(Formerly known as Saveto PU1)

Vetoflex SS783

High quality elastic one component moisture cure silicone sealant

Vetoflex PS787

Two-component trafficable, jet fuel resistant heavy duty pitch-polysulphide sealant.

Featured Product
Vetotop EL392

Industrial grade self smoothening epoxy based floor topping from 0.8 to 2 mm thickness

Uses
Industrial kitchens and food processing plants
Heavy duty vehicle factories, car parks and aircraft hangers
Clean rooms, battery rooms and laboratories
Any flooring were impact resistance is of importance
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map
Home
About us
news and events
Contact
DOWNLOAD SECTION
REFERENCES
Copyright ©2015-2016 Saudi Vetonit Co. Ltd. All Rights Reserved.