Flooring & Coatings Systems
Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed.

Leveling of concrete slabs prior to application of final floor coverings.
Screeding over hollow-core pre-cast concrete slabs.
Leveling floors and slabs to slope to ensure proper flow to drains.
Fast Download
Flooring Technical Brochure
download (*.pdf 9.29Mb)
Technical Information
Product Description

Vetotop CS536 is a single component cementitious floor screed composed of hydraulic binders, silica sand, selected aggregates special additives and fibers. It is supplied as a dry powder in pre-weighed bags ready to use on site, once mixed it will form a trowellable mortar that is applied in thicknesses between 30 and 100 mm.

  • Factory controlled pre-blend ensures consistent high quality.
  • Suitable for Middle East harsh weather conditions.
  • Easy application enabling high productivity & superior finishing.
  • High bond to substrate.
  • Excellent physical and mechanical properties.
  • Shrinkage compensated.
  • Excellent workability.
  • Fiber reinforced resisting crack formation.
Compliance Standard
  • EN197: 2011
  • ASTM C109
  • EN13813:2002
  • BS8204:2010
Packaging & Coverage

Vetotop CS536 supplied in 50 Kg Bag. Yield : 21.7 - 27.8 Ltr

Shelf Life & Storage

Original sealed bag of Vetotop CS536 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place at temperatures between +5ºC - 35ºC.

Grey Colour
Application Information
Instructions for use

For the preparation of mixture, pour into a container 5-6 liters of water for 50 Kg bag of Vetotop CS536.
Add the powder to the water and mix with a low speed electric drill fitted with a suitable paddle, until a uniform, lump free consistency mix is achieved. No further water should be added to the mix. Do not add water to the mix once its start to set.

Pour the mixed product onto the surface and spread to the desired thickness using steel trowel or suitable tools.
Cure the screed as per standard concrete curing practices. Do not subject the screed to vehicular traffic for 28 days till ensure full cure and systems ability to withstand designed traffic loads.
A concrete sealer is required for enhancing the screed durability and resistance to ingress of water, apply Vetoseal XW770 at a rate of 8 to 12 m2 per liter. Make sure that the sealer is uniformly applied and covering all screed surface.

Clean tools with water promptly before material hardens. Hardened material can be mechanically removed.

Surface Preparation

Surface Preparation
The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.

Vetotop CS536 can be laid as a bonded screed by applying Vetobond PB434 slurry to prepared concrete substrate as a bonding and priming layer, alternatively and epoxy bonding agent can be used such as Vetobond EB430 or EB431.

To prepare the slurry primer mix 1 volume of VetoBond PB434 to 1 volume of clean water with 3 volumes of fresh cement and mix until a smooth consistency is prepared. Scrub the mixed slurry into the concrete surface, while the slurry is wet apply Vetotop CS536 in order to insure good adhesion with the substrate.

  • Do not apply the product at temperature less than +5ºC.
  • Vetotop CS536 should be checked for its suitability when concrete is steam cured. Also carry out prior test for its suitability when gypsum or colored mixes are being used.
  • For further information contact our technical department.
Additional Information
Health & Safety

Vetotop CS536 is highly alkaline therefore avoid direct contact with eyes or skin. Vetobond PB434 is latex emulsion. It is recommended to use protective gloves and goggles during application.
Any skin contact should be washed with plenty amount of water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.
Vetotop CS536 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.


More Products from this section
Vetodeck UD

Polyurethane based heavy duty, waterproof and UV resistant car park decking system

Vetotop CL530

Premixed 2 to 10 mm thick cementitious self leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed.

Vetotop EC198

Water Based chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating

Vetotop EC493

Solvent based high performance, self priming, thin epoxy topping

view more
Featured Product
Vetorep CR526

High strength fine structural repair mortar

Repair of broken structural concrete elements.
Vertical concrete repair up to 40 mm in a single layer.
Overhead concrete repair up to 20 mm in a single layer.
Horizontal and patch repairs up to 50 mm in a single layer.
General curbstone & concrete repairs.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map