Solvent based high performance, self priming, thin epoxy topping
Vetotop EC495 is a two component high performance solvent based epoxy coating system that adheres perfectly to a variety of substrates like: concrete, metal, wood, stone, etc. Once cured, the product has excellent abrasion and chemical resistance. Vetotop EC495 provides an attractive hard wearing and easily cleanable floor finish. Its use on floors and walls will enhance lighting in the environment due to the product reflective properties.
BS EN476:2009 as class 1 in flame spread.
Vetotop EC495 supplied in 4 Liter Kit. Yield - 10 m²/Liter @ 100 micron wft.
Original sealed bag of Vetotop EC495 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.
Vetotop EC495 is designed to be a hard wearing two coat application on cementitious or metal substrates. When used on metal substrates, it is recommended that the application takes place within 2 to 3 hours from substrate preparation to prevent early rust formation. The applied product will be resistant to water as well as a wide range of chemicals.
The individual components of Vetotop EC495 should be thoroughly stirred before the two are mixed together. The entire contents of the hardener container should be poured into the base container and the materials mixed thoroughly for at least 3 minutes. The use of a heavy-duty slow speed, flameproof or air driven drill fitted with a mixing paddle is desirable.
The mixed Vetotop EC495 should be applied to the prepared surface using a brush or lambs-wool roller. Ensure that the area is completely coated and that ‘ponding’ of the material does not occur.
The applied coating can receive foot traffi c in 24 hours, however it shall be allowed to cure for 7 days to achieve full cure to receive vehicular traffi c and its chemical resistance properties.
Vetotop should be removed from tools and equipment with Vetonit Solvent XX400 immediately after use. Hardened material can only be removed mechanically.
The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Laitence and weak surface layer shall be removed using mechanical methods such as grinding or blasting in order to provide a sound well profi led surface. All necessary repairs should be made prior to application
by using epoxy mortar from Vetorep ER range.
New concrete floors shall be at least 28 days old with moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).
Steel substrates should be grit blasted to surface quality SA2½ (BS 4232:Second Quality) and application shall take place within 2 to 4 hours after blasting.
Vetotop EC495 and Vetonit Solvent XX400 should not come into contact with skin and eyes or be swallowed. Ensure adequate ventilation and avoid inhalation of vapors. Some people are sensitive to resins, hardeners
and solvents. Wear suitable protective clothing, gloves, and eye protection. If working in confined areas, suitable respiratory protective equipment must be used.The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medial advice. If swallowed, seek medical attention immediately - Do not induce vomiting.
Vetotop EC495 and Vetonit Solvent XX400 are flammable. Keep away from sources of ignition. No Smoking. In the event of fire extinguish with CO2 or foam.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Polyurethane based heavy duty, waterproof and UV resistant car park decking system
Premixed 2 to 10 mm thick cementitious self leveling underlayment
Premixed 10 to 30 mm thick cementitious screed.
Premixed 30 to 100 mm thick cementitious screed.
Water Based chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating
Cementitious based adhesive and base coat for EIFS / ETICS