Renders & Finishes
Vetonit Crack Filler

High quality premixed surface crack filler

Filling static cracks up to 4 mm, blow holes and minor undulations etc.
Applied externally & internally in wet to dry conditions onto the walls & ceilings such as Bathrooms & Kitchens.
On concrete and plastered surfaces that are smooth and also precast concrete surfaces.
Fast Download
reference projects
Al Jouf University Project
Saudi Arabia
Safari Contracting Company
Technical Information
Product Description

Vetonit Crack Filler is composed of a fine filler, high quality white cement, bonding chemicals and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce cohesive mix. Vetonit Crack Filler is a high quality product for repairing static cracks and provides very smooth surface finish for subsequent application of paints, decorative coatings & wallpapers. Vetonit Crack Filler can be applied in crack thickness from scrape coat to 4 mm.

  • Factory controlled pre-blend ensures consistent high quality
  • Requires only addition of water on-site at the time of usage
  • Suitable for External & Internal applications
  • Cured material is water resistant
  • Easy application with superior finishing achieved in minimum efforts
  • Strong adhesion on variety of substrates
  • Concrete and plastered walls & ceilings
  • Very smooth finish can be achieved
  • Suitable for humid & dry conditions
Compliance Standard
  • ASTM C348
  • ASTM C109
Packaging & Coverage

Vetonit Crack Filler supplied in 1.5 & 25 Kg Bag
Cconsumption: 0.8 - 1.0 Kg/m² 1mm Thickness

Shelf Life & Storage

Original sealed bags of Vetonit Crack Filler has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

White Colour Powder
Application Information
Instructions for use

For mechanical mixing add to the mixing container 9.5-11.0 litres of water for each 25 Kg bag of Vetonit Crack Filler or 0.57-0.66 litres/1.5 kg small bag. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
Leave the mixed material to stand for 10 min and briefly remix without addition of water. Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when homogenous mix is achieved.
When required add 0.5 Ltr of Vetonit Bond 2 to the mixing water and adjust the water requirement accordingly for each 25 kg bag or 30 ml of Vetonit Bond 2 per 1.5 kg bag. Follow the same mixing procedure as above.
Mixed material must be used within 2 hours.
Do not add water once the mixed filler mortar start to stiffen or harden.

Vetonit Crack Filler is generally applied in two coats for wide and deeper cracks.
Apply Vetonit Crack Filler to the substrate by pressing the filler firmly into the cracks using flat putty trowel.
Use Vetonit Joint Tape to cover the treated surface after filling the cracks. Use Vetonit Bond 2 for fixing tape for better adhesion.
Use alkali resistant paints & coatings as a final decorative finishes.


Vetonit crack filler generally may not require curing. However in extreme weather conditions (T > 45 C° and RH < 50% ) Vetonit crack filler should be cured by spraying clean water every 8-12 Hrs for a minimum 2 days.

All tools should be cleaned immediately after finishing by water. Hardened materials can be cleaned mechanically.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Prior to Vetonit Crack Filler application, wet the entire surfaces with clean potable water and allow to become damp at the time of application.

Additional Information
Health & Safety

Vetonit Crack Filler is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.
Vetonit Crack Filler is non-flammable.
For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section

Water resistant internal use premix smooth cement coating


Water resistant external use premix smooth cement coating

Vetonit Gypsum Joint Compound

Premium quality premixed compound for gypsum board joints

Vetonit Putty WR

Water resistant high quality premixed putty

Vetonit Base WR EG

Weather Resistant Premix Cement Coating for External Use

view more
Featured Product
Vetotouch TEXTURA

Acrylic polymer modified decorative finish coat applied at thicknesses from 3 to 20 mm

External and internal building facades.
As a finish coat for of EIFS / ETICS systems.
Block walls and concrete surfaces.
On scratch coated overhead surfaces.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map