UV resistant trafficable polyurethane coating
Vetotop UC370 is a two component, low viscosity acrylic urethane top coat. Vetotop UC370 recommended as a top coat for steel substrates after the mandatory priming by Vetoprime EP390. It is used as UV resistant sealer over concrete and the range of VetoFloor epoxy and polyurethane flooring & coating systems. Vetotop UC370 is UV stable for use in exterior applications, cures rapidly and the sealed system is ideal for all weather exposure. When used as a finish coat, Vetotop UC370 gives a hard, gloss surface that offers excellent stain resistance and easy cleanability. Vetotop UC370 is supplied in a pack size of 4 & 15 liter kit consist of Resin & Hardener.
Vetotop UC370 supplied in 4 & 15 Liter Kits. Theoretical Coverage - 7 m2 / Liter.
Vetoprime EP491 supplied in 4 Liter Kits.Theoretical Coverage - 8 m2 / Liter.
Original sealed kit of Vetotop UC370 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.
Mixing Vetotop UC370
In a separate mixing vessel, use a slow speed mixer to mix the base, hardener for 3 minutes. Mix these components in the quantities supplied taking care to ensure all containers are scraped clean. Do not add solvent thinners at any time.
Application
Apply Vetotop UC370 by roller or airless spray to the surface. Vetotop UC370 can be sprayed at a thickness of 125-150 micron (50% solids), so the application coverage rate should be at 7 m2/liter per coat.
Application should not be carried out when humidity exceeds 85%, or when the surface temperature to be coated is less than 3°C above the dew point.
Vetotop UC370 can be applied as a single coat, or as a multi coat sandwich system incorporating Vetograin products to give a slip resistant finish.
For more information, please refere to Vetograin Technical Data Sheet.
Re-coating time is 24h max if temp >25C."
Expansion Joints
Expansion joints in the existing substrate must be retained and continued through the Vetotop UC370 topping. Saveto have a range of joint sealants specifically designed for flooring (see Vetoflex PU781, Vetoflex PS782 and Vetoflex PS786 product data sheets).
Cleaning
Tools and equipment should be cleaned with Vetonit Solvent XX300 immediately after use.
The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Laitence and weak surface layer shall be removed using mechanical methods such as grinding or blasting in order to provide a sound well profiled surface. All necessary repairs should be made prior to application by using epoxy mortar from Vetorep ER range.
New concrete floors shall be at least 28 days old with moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).
Design Criteria
Vetotop UC370 is designed to be applied by roller or airless spray in two or more coats at a thickness of 500 microns per coat. The product is designed to resist ultra violette rays (UV) while being trafficable and abrasion resistant.
Vetotop UC370 is irritant and harmful therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. In case of contact with eyes, clean immediately with plenty of clean cold water and seek medical advise.
Ensure adequate ventilation when using product or when using solvent for cleaning purposes and avoid inhalation of vapours.
The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medial advice. If swallowed, seek medical attention immediately - Do not induce vomiting.
Vetotop UC370 and Vetonit Solvent XX300 are flammable. Keep away from sources of ignition. No Smoking. In the event of fire extinguish with CO2 or foam.
Refer to product(s) MSDS for further information.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Polyurethane based heavy duty, waterproof and UV resistant car park decking system
Premixed 2 to 10 mm thick cementitious self leveling underlayment
Premixed 10 to 30 mm thick cementitious screed.
Premixed 30 to 100 mm thick cementitious screed.
Water Based chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating
Polymer modified hygienic cementitious fine non sanded tile grout for hospitals & clinics