Plasters & Masonry
Masonry Grout Filler

Premixed cementitious masonry grout

Masonry Grout Filler can be applied on cement based masonry blocks, masonry units, behind marble and cement panels, tiles or slabs, etc.
Masonry Grout Filler is also suitable for application behind gypsum boards
Fast Download
Decorative Coating Brochure
download (*.pdf 2.78Mb)
Plastering Systems Technical Guide
download (*.pdf 9.93Mb)
reference projects
King Khalid University
Saudi Arabia
Housing & Parking projects
Al Jabreen Contracting
Parking: Zuhair Fayez Housing: Saud Consult
Technical Information
Product Description

Masonry Grout Filler is a fine grout category as defined by American Concrete Institute (ACI), and composed of portland cement, natural sand, selected fine aggregates and special additives. The Masonry Grout Filler contains admixtures in accordance to ASTM C 476, C207, C260 to meet fine grout category. Masonry Grout Filler is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce pourable grout.  Masonry Grout Filler is ideal for grouting masonry blocks, masonry units, cores and also as a filler behind marble slabs etc.. 

  • Factory controlled pre-blend ensures consistent high quality
  • Requires only addition of water on-site at the time of usage
  • Suitable for ME harsh weather conditions
  • Easy application with uniform work flow enables high productivity & superior finishing
  • Strong adhesion
  • Good mechanical resistance
  • Excellent workability
Compliance Standard
  • ASTM C 476, C207
  • ASTM C 404, C260
  • ASTM C 150 Type 1
Packaging & Coverage

Masonry Grout Filler is supplied in 50 Kg Bag
Yield: 28.8 Lit wet/ 1 (50Kg) bag powder

Shelf Life & Storage

Original sealed bags of Masonry Grout Filler has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place at temperatures between +5ºC - 35ºC.

Application Information
Instructions for use


For the preparation of masonry grout mixture, pour into a container 7.75-8.25 litres of water for each 50 Kg bag of Masonry Grout Filler.

Slowly add the powder to the water while mixing with electric drill fitted with a suitable paddle for 2 minutes. Then continue mixing at medium-high speed for another 2-3 minutes, until a uniform, lump free pourable consistency mix is achieved. Total mixing time is 4-5 minutes approx. Do not add water to the mix once it starts to stiffen.


Pour the mixed material into the gap between masonry blocks, cement panels or behind marble or gypsum board within the open time of 30-45 min.

Avoid air entrapment between the gaps while pouring the grout material.

For high lift grouting, the mixed material should be pumped or poured from a height to ensures the desired grout flow so that it spreads smoothly within the gaps.

We recommend use of mechanical grout pump for placement of masonry grout as it will give more efficient filling and also help in grout pumping in high rise structures.


All tools should be cleaned immediately after finishing by water. Hardened materials can be cleaned mechanically.

Surface Preparation

The surface should be sound, clean free from loose materials, grease, laitance, dust etc.

Additional Information
Health & Safety

Masonry Grout Filler is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.

Masonry Grout Filler is non-flammable. For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Acoustic Plaster

High quality light weight premixed acoustic plaster

Gypsum Plaster

High quality gypsum plaster.

Plaster Cement Perlite

Sprayable premixed plaster

Plaster Gypsum PERLITE

Light weight gypsum perlite plaster

Plaster Mix M

Manual Applied Premixed Plaster


view more
Featured Product
Vetoproof CM744

Polymer modified water resistant cementitious top coat

As a textured protective and decorative cementitious finish for boundary walls, blocks, concrete..etc.
Waterproofing under tiles in wet areas
To protect atmospherically exposed reinforced concrete structures from attack by acid gases, chloride ions, oxygen and water
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map