Plasters & Masonry
Vetonit Masonry Mortar

Premixed cementitious masonry mortar

Masonry Mortar can be used internally or externally in wet & dry conditions onto block walls & rough surfaces.
Masonry Mortar can be used for cement & concrete blocks and panels.
Masonry Mortar can be used for filling walls and connections.
Fast Download
reference projects
King Abdullah Sports City, Hall and Stadium
Saudi Arabia
Multipurpose Sports Hall and Athletics Stadium
El-Seif Engineering Contracting Co. & Hyundai Heavy Industrial Consortium
Technical Information
Product Description

Masonry Mortar is a cement based coat composed of hydraulic binders, selected aggregates and high performance additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce cohesive mortar. Masonry Mortar is a premium quality product contains special adhesion additive. Masonry Mortar can be applied in thickness from 5 mm to 50 mm.

  • Factory controlled pre-blend ensures consistent high quality
  • Requires only addition of water on-site at the time of usage
  • Suitable for ME harsh weather conditions
  • When using the Silo system, an easy application with uniform work flow enables high productivity & superior finishing
  • Strong adhesion on variety of concrete Blocks
  • Strong bond in blocks & wall connections
  • Internal & external applications
  • Suitable for wet to dry conditions
Compliance Standard
  • ASTM C348 & C109
  • ASTM C270 & C780
  • BSEN 998-2, Type G
  • ASTM C1072
Packaging & Coverage

Masonry Mortar supplied it 50 Kg Bag

Coverage: 15 L.M/ 10mm (Solid block 400x200x200 mm)

                22 L.M/ 10mm (Solid block 400x200x150 mm)

                31 L.M/ 10mm (Solid block 400x200x100 mm)

Shelf Life & Storage

Original sealed bags of Masonry Mortar has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place at temperatures between +5ºC - 35ºC.

Application Information
Instructions for use


Add to the mixing container 8 - 10 litres of water for each 50 Kg bag of Masonry Mortar. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lumpfree consistency is achieved.

Leave the mixed material to stand for 10 min and briefly remix without addition of water.

Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when homogenous mix is achieved.



Neutralize the suction of the block surface with water before applying mortar. Any excess water should be removed.

The masonry mortar is spread with trowel on the surface and joints where the blocks are to be mounted.

Fill joint in similar way as conventional sand/cement mortar.

After stiffening, the masonry mortar should be given a final smoothing to remove protrusions and eliminates undulations.


All tools should be cleaned immediately after finishing by water. Hardened materials can be cleaned mechanically.

Surface Preparation

Block surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.

Prior to Masonry Mortar application, wet the entire surfaces with clean potable water and surface should look damp at the time of Masonry Mortar application.

Additional Information
Health & Safety

Masonry Mortar is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.

Masonry Mortar is non-flammable.

For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Acoustic Plaster

High quality light weight premixed acoustic plaster

Gypsum Plaster

High quality gypsum plaster.

Masonry Grout Filler

Premixed cementitious masonry grout

Plaster Cement Perlite

Sprayable premixed plaster

Plaster Gypsum PERLITE

Light weight gypsum perlite plaster

view more
Featured Product
Vetorep ER352

Twin Pack Putty Formulated for Thick Vertical and Overhead Applications

Repair of concrete surface pores, blemishes at thickness from feather edge.
Sealing of surface cracks in aggressive environments and in injection repairs.
Leveling of surface imperfections and irregularities prior to application of Saveto resinous coatings and toppings range.
Fixing and bedding of tiles, dowels and anchors.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map