Renders & Finishes
Vetonit Putty WR

Water resistant high quality premixed putty

Leveling of minor surface undulations
Applied externally & internally in wet to dry conditions onto the walls & ceilings such as bathrooms & kitchens
On concrete and plastered surfaces that are smooth and also precast concrete surfaces
Suitable for use over surfaces that are plastered with Saveto products and on gypsum boards
Fast Download
Technical Information
Product Description

Vetonit Putty WR is composed of a fine fillers, bonding chemicals and high performance additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce cohesive mix. Vetonit Putty WR is a high quality product as thin underlayment to repair undulations and provides very smooth surface finish ideal for subsequent application of paint & decorative coatings. Vetonit Putty WR can be applied generally in thickness from: 1 mm to 3 mm.

  • Factory controlled pre-blend ensures consistent high quality
  • Requires only addition of water on-site at the time of usage
  • Suitable for External & Internal applications
  • Water resistant
  • Easy application with superior finishing achieved in minimum efforts
  • Strong adhesion on variety of substrates
  • Concrete and plastered walls & ceilings
  • Very smooth finish can be achieved
  • Suitable for humid & dry conditions
Compliance Standard
  • BS EN 1015-12 
Packaging & Coverage

Vetonit Putty WR supplied in 20 Kg Bag
Consumption: 1.0 - 1.2 kg/m2/1mm Thickness

Shelf Life & Storage

Original sealed bags of Vetonit Putty WR has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

White colour Powder
Application Information
Instructions for use

For mechanical mixing add to the mixing container 7.6-8 litres of water for each 20 Kg bag of Vetonit Putty WR. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
Leave the mixed material to stand for 10 min and briefly remix without addition of water.
Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when homogenous mix is achieved.
When required add 1 litres of Vetonit Bond 2 to the mixing water and adjust the water requirement accordingly for each 20kg bag. Follow the same mixing procedure as above.
Mixed material must be used within 3 hours. Do not add water once the mixed filler mortar start to stiffen or harden.

Vetonit Putty WR is generally applied in single or double coats. Apply Vetonit Putty WR to the substrate by pressing the putty firmly, work the mixed material to a smooth level using flat trowel. Apply second coat as necessary once the first coat has initially set.
Once Vetonit Putty WR is applied, It is recommended to apply one coat of alkali resistant primer followed by two coats of acrylic emulsion paint or other suitable coatings.

Vetonit Putty WR is self curing and do not require water treatment. However when used as a final finish it is recomended to apply a single coat of Bond Pure to perform as a surface enhancer and curing compound that will naturally disintegrate with time.

All tools should be cleaned immediately after finishing by water. Hardened materials can be cleaned mechanically.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Prior to Vetonit Putty WR application, wet the entire surfaces with clean potable water and allow to become damp at the time of application.

Additional Information
Health & Safety

Vetonit Putty WR is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application.
Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.
Vetonit Putty WR is non-flammable.
For further information, please refer to material safety data sheet.

Important note
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetonit Crack Filler

High quality premixed surface crack filler


Water resistant internal use premix smooth cement coating


Water resistant external use premix smooth cement coating

Vetonit Gypsum Joint Compound

Premium quality premixed compound for gypsum board joints

Vetonit Base WR EG

Weather Resistant Premix Cement Coating for External Use

view more
Featured Product

High quality ceramic tile adhesive for projects.


For ceramic tiles.
Tiling on smooth concrete surfaces, lightweight bricks, blocks, plaster boards.
Tiling on wall surfaces that are plastered with water resistant plasters such as Vetonit Render & Vetonit Base WR on damp concrete interiors.
Suitable for dry & wet conditions.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map