Wall & Facade Systems

Grooved decorative finish coat

Special grooved-graffio finish interior/exterior application.
As a finish coat for of EIFS / ETICS systems.
On plastered, fairfaced concrete surfaces.
On pre-cast panels.
3-4 mm thickness
Fast Download
Decorative Coating Brochure
download (*.pdf 2.78Mb)
External Thermal Insulation Composite System - ETICS
download (*.pdf 8.19Mb)
Technical Information
Product Description

Vetotouch Graviatto is a cement based decorative finish composed of hydraulic binders, selected aggregates and special additives . It is supplied as a dry powder in a pre-weighed bags ready to use on site, which requires only addition of clean water to produce easily workable mortar. 

  • Factory controlled pre-blend ensures consistent high quality
  • Requires only addition of water on –site at the time of usage.
  • Provides profiled and scratched finishes.
  • Improved workability and curing
  • Easy application with uniform work flow enables high productivity and superior finishing.
  • Strong adhesion on variety of substrates.
  • Internal and external applications.
  • Weather resistant.
  • UV stable pigment provides resistance to fading and eliminates need for additional paint
  • Suitable for humid and dry condition.
Compliance Standard
  • EN 998:2010
    EN 926:2011
    EN 13914:2005
    EN 1015:2000
Packaging & Coverage

Vetotouch Graviatto supplied in 25 Kg Bag
Coverage - 1.4 Kg / m2 / mm

Shelf Life & Storage

Original sealed bags of Vetotouch Graviatto has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Saveto Standard Colors
Application Information
Instructions for use


Add to the mixing container 7.5-8.5 liters of water for each 25 kg bag of Vetotouch Graviatto. Add the powder to the water and mix with a mechanical plaster mixer or low speed heavy duty electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump free consistency is achieved. Leave the mixed material to stand for 10 min and briefly remix without addition of water.
Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when homogeneous mix is achieved.
Where manual application is made (not by spray machines), you can optionally add 0.5 to 1.0 liter of Vetobond AB432 to the mixing water and adjust the water requirement accordingly for each 25 kg bag. Follow same mixing procedure as described above.
Mixed material must be used within 30-60 minutes.
Do not add water, once the mixed mortar start to harden.

Vetotouch Graviatto can be applied in one or two layers up to 3mm/Coat. Allow the first layer to partially dry (30 to 120 minutes depending on weather conditions) before applying the second layer.
After applying the layers by steel trowel, wait for about 10 - 15 minutes and then use special plastic trowel to get groove effects. To protect Vetotouch Graviatto, apply Vetoseal XX772 by brush or spray machine after three days of curing.

Vetotouch Graviatto is best cured by spraying an acrylic based curing compound on the surfaces of applied materials. Manual curing can be used, however it is critical that water is sprayed uniformly on the surface keeping it moist at all times for a period of 3 days

Additional Information
Health & Safety

Vetotouch Graviatto is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.

Vetotouch Graviatto is non-flammable. For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Cool Plaster

Advanced modified cementitious thermal insulating plaster


Cool Mortar

Advanced modified cementitious light weight, thermal insulating masonry mortar 


Vetotherm FLEX

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm ULTRA

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm Plaster

Advanced Modified Cementitious Thermal Insulating Plaster

view more
Featured Product
Vetotop UC372

High performance, matt finish chemical, scratch & UV resistant polyurethane floor & wall coating

long term protection of car parks and floors in factories, warehouses, laboratories, loading decks ramps, showers, kitchens, dairies, breweries.
UV Resistant top coat over flooring systems including concrete, epoxies, aromatic elastic polyurethanes,...etc.
Connected products
Vetotouch Repara

Dual component cementitious coating and color nuetralizer for...

Vetotouch TYROLEAN

Exterior decorative textured render

Vetotouch TEXTURA

Acrylic polymer modified decorative finish coat applied at...

Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map