Jordan
Bahrain Egypt Saudi Arabia UAE
EN
EN
Contact news and events About us Home
PRODUCT RANGE
SYSTEM
Selector REFERENCES DOWNLOAD SECTION
Wall & Facade Systems
Vetotouch TYROLEAN

Exterior decorative textured render

Uses
Special Stenciled and textured finishes designed for interior/exterior application.
As a finish coat for of EIFS / ETICS systems.
On plastered, fairfaced concrete surfaces.
On block walls and pre-cast panels.
3-6 mm thickness.
Fast Download
Technical Data Sheet
download (*.pdf 0.21Mb)
Method of Statement
download (*.pdf 0.21Mb)
MSDS
download (*.pdf 0.21Mb)
Catalogues
Decorative Coating Brochure
download (*.pdf 2.78Mb)
External Thermal Insulation Composite System - ETICS
download (*.pdf 8.19Mb)
Technical Information
Product Description

Vetotouch Tyrolean is a cement based decorative finish composed of hydraulic binders, selected aggregates and special additives . It is supplied as a dry powder in a pre-weighed bags ready to use on site, which requires only addition of clean water to produce easily workable mortar. 

Advantages
  • Factory controlled pre-blend ensures consistent high quality
  • Requires only addition of water on –site at the time of usage.
  • Provides textured and stenciled finishes.
  • Improved workability and curing
  • Easy application with uniform work flow enables high productivity and superior finishing.
  • Strong adhesion on variety of substrates.
  • Internal and external applications.
  • Weather resistant.
  • UV stable pigment provides resistance to fading and eliminates need for additional paint
  • Suitable for humid and dry condition.
Compiliance Standard
  • EN 998:2010
  • EN 926:2011
  • EN 13914:2005
  • EN 1015:2000
Packaging & Coverage

Vetotouch Tyrolean supplied in 25 Kg Bag
Coverage - 1.5 Kg / m2 / mm Thickness

Shelf Life & Storage

Original sealed bags of Vetotouch Tyrolean has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Colors
Saveto Standard Colors
Application Information
Instructions for use

Mixing

Add to the mixing container 7-8 liters of water for each 25 kg bag of Vetotouch Tyrolean. Add the powder to the water and mix with a mechanical plaster mixer or low speed heavy duty electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump free consistency is achieved. Leave the mixed material to stand for 10 min and briefly remix without addition of water.

Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when homogeneous mix is achieved.
Add 0.5 to 1.0 liter of Vetobond AB432 to the mixing water and adjust the water requirement accordingly for each 25 kg bag. Follow same mixing procedure as described above.
Mixed material must be used within 30-60 minutess.
Do not add water, once the mixed mortar start to harden.

Application
VetoTyrolean can be applied in one or two layers up to 6 mm/coat. Apply by hopper Gun or by Terol hand operated machine.
To protect Vetotouch Tyrolean; apply Vetoseal XX772 by brush or spray machine after three days of curing.

Curing
Vetotouch Tyrolean is best cured by spraying an acrylic based curing compound on the surfaces of applied materials.

 

Additional Information
Health & Sefety

Vetotouch Tyrolean is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.

Vetotouch Tyrolean is non-flammable. For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Cool Plaster

Advanced modified cementitious thermal insulating plaster

 

Cool Mortar

Advanced modified cementitious light weight, thermal insulating masonry mortar 

 

Vetotherm FLEX

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm ULTRA

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm Plaster

Advanced Modified Cementitious Thermal Insulating Plaster

view more
Featured Product
Vetonit Bond Pure

Multipurpose bonding agent & admixture

Uses
Works as admixture with plaster, lime/sand cement screeds, renders, mortars and cement grouts when diluted 1:7 with potable water.
Works as bonding agent and can be sprayed or brushed on green substrates to improve bonding of plasters, patching compounds. Renders, mortars, joint tape fixing etc. when diluted 1:3 with potable water.
Can be used for both internal and external applications.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map
Home
About us
news and events
Contact
DOWNLOAD SECTION
REFERENCES
Copyright ©2015-2016 Saudi Vetonit Co. Ltd. All Rights Reserved.