Jordan
Bahrain Egypt Saudi Arabia UAE
EN
EN
Contact news and events About us Home
PRODUCT RANGE
SYSTEM
Selector REFERENCES DOWNLOAD SECTION
Concrete Grouts, Repairs, & Enhancements
Vetorep ER450

Abrasion resistant flexible epoxy based transition mortar

Uses
Transition mortar betwen bridge decks and mechanical expansion joints.
Interface between asphalt and concrete slabs.
Interface between steel and concrete elements
Where a trafficable yet flexible mortar is needed.
Fast Download
Technical Data Sheet
download (*.pdf 0.25Mb)
Method of Statement
download (*.pdf 0.21Mb)
Technical Information
Product Description

Vetorep ER450 is a three component system consisting of solvent free epoxy resins together with a special blend of fillers to provide a flexible trowel grade epoxy mortar. The mixed mortar is designed for use in bridge and highway transitioning joints and between concrete, asphalt and steel.

Advantages
  • Solvent free.
  • Hard wearing with high abrasions resistance.
  • Excellent adhesion to concrete, asphalt and steel surfaces.
  • Withstand dynamic movement.
  • Fast cure.
  • No priming is required.
  • Flexible mortar.
Compiliance Standard

EN 1504:2013

Packaging & Coverage

Vetorep ER450 is supplied in 25 Kg kits with a Theoretical Yield of 14 Liters/Kit

Shelf Life & Storage

Original sealed kits of Vetorep ER450 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded temperature controlled place <25ºC.

Application Information
Instructions for use

Application


Vetorep ER450 should be applied by first tamping, followed by trowelling using steel float.

Cleaning

Vetorep ER450 should be removed from tools, equipment and mixers with Vetonit Solvent XX immediately after use.
Vetorep ER450 should be allowed to cure for 24 hours at 25°C before being subjected to foot traffic. At the same temperature, full mechanical and chemical properties are achieved after 7 days (please consult Saveto Technical Department for details of curing times at other temperatures).

Surface Preparation

Surface Preparation

The surface must be structurally sound, free from oil, grease and other forms of contamination. Concrete should be surface dry and suitably prepared either by scabbling or grit blasting to remove any surface

Mixing

Vetorep ER450 comprises of three components, a resin base, hardener and filler which are pre-weighed to the correct proportions. Under no circumstances should part mixing be carried out.
Ensure that the bottom and sides of resin containers are thoroughly scraped; transfer the entire contents of the hardener container into the base container. Using a mixing paddle attached to a heavy duty slow speed electric drill, mix for approximately 2 minutes until a uniform consistency is obtained.
The resin mixture should then be transferred to a separate container or forced action pan mixer, and the FILLER gradually added and mixed for a further 2 minutes or until the filler has thoroughly wetted out and a uniform consistency is obtained.

Additional Information
Health & Sefety

Vetorep ER450 contains epoxy resin and coal tar which may cause skin sensitisation in certain individuals. Skin contact should be avoided and a suitable barrier cream applied or disposable rubber or plastic gloves worn. Also use eye/face protection. If contact with skin occurs, it must be removed before it hardens followed by washing with soap and water. In case of contact with eyes rinse immediately with plenty of water and seek medical treatment immediately.
Do not smoke during use. Do not use near a naked flame.
Flash point >60ºC.
For further information, refer to the Product Material Safety Data Sheet.

 

 

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor EG346

Epoxy resin twin cartridge anchoring grout

vetoanchor PG347

Polyester injection and anchoring grout

Vetocure XT425

Water based concrete curing compound

Vetocure XT426

Multi-Purpose Acrylic Resin Curing Compound

Vetocure XT427

Water based acrylic curing compound and primer *

view more
Featured Product
Vetoset CA540

Professional grade adhesive to work with large tile format & multiple types of tiles (C2TE...

Uses
For Ceramic tiles, natural stone conglomerates (Granite & Marble, Terrazo) , Porcelain, Artificial Stone and Large format tiles.
Laying of large format heavy tiles in internal and external applications.
Tile over tile applications & with heated screeds.
Laying on flexible substrates as well as dry walls (gypsum and cement boards)
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map
Home
About us
news and events
Contact
DOWNLOAD SECTION
REFERENCES
Copyright ©2015-2016 Saudi Vetonit Co. Ltd. All Rights Reserved.