Flooring & Coatings Systems
Vetotop CX534

Premixed 20 to 100 mm thick conventional cementitious mortar.

Cost effective cavity filling in non-structural areas.
Non-structural backing mortar.
Filling around underfloor heating installations and mechanical fittings.
As a bedding mortar for granite and marble.
Fast Download
Flooring Technical Brochure
download (*.pdf 9.29Mb)
Technical Information
Product Description

Vetotop CX534 is a single component cementitious backing mortar composed of hydraulic binders, silica sand and selected aggregates. It is supplied in bulk as a dry pumpable powder ready to use on site, once mixed it will form a trowellable mortar that is applied in thicknesses between 20 and 100 mm.

  • Factory controlled pre-blend ensures consistent high quality. 

  • Suitable for Middle East harsh weather conditions.

  • Easy application enabling high productivity through pumps and horizontal mixers. 

  • Easy to break and refurbish backing to install additional piping and mechanical fittings.

  • Excellent workability. 

  • Replaces conventional site batched mortars.

  • Applied on horizontal damp compacted sand and cementitious substrates while providing good adhesion.

  • Contains special additive that reduces friction and prolongs lifespan of equipment.

Compliance Standard

- ASTM C 150
- ASTM C 207
- ASTM C 136

Packaging & Coverage

Vetotop CX534 is supplied in 50kg bag or Bulk, Yield: 0.5 - 0.6 Ltr / Kg

Shelf Life & Storage

Vetotop CX534 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.

Grey & white color powder
Application Information
Instructions for use


Vetotop CX534 can be applied in a single layer to the desired thickness using HM 24 machine. Rod or screed to a uniform thickness immediately then follow with installation of the tiles. To insure better coverage increase the thickness and firmly press on the tile squeezing the excess out. For better adhesion you can use Vetobond PB434 product call technical engineer for advice.


Vetotop CX534 is best cured by spraying water on the surfaces of the tiles before grouting for 2-3 days. During hot & dry conditions allow curing for minimum of 5 days. 


Clean tools with water promptly before material hardens. Hardened material can be mechanically removed.

Surface Preparation

Surface Preparation

Substrate should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc. Prior to Vetotop CX534 Application, wet the entire surfaces with clean potable water and surface should look damp at the time of application.


For manual mixing, add to the mixing container 9-10.5 liters of water to each 50kg bag of Vetotop CX534. Add the powder to the water and mix with mechanical mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.

For application using HM 24 Mixing & pumping machine, the water flow rate is 300-500 Lit/hour. Mixed material should be used within 1 hour.

Re-tempering is allowed between 60 and 90 minutes for one time only.

Smooth Concrete Surfaces

Apply Vetobond PB433 or Vetobond EB430 as a primer coat or prepare the horizontal substrate by chopping or chiseling.


Design Criteria

Vetotop CX534 is designed for application for pumpingmachine (HM 24) and contains special shrinkage control additive and provides good adhesion. The product is available in grey and white color and can be applied in thickness from 2 to 10 cm.

Additional Information
Health & Safety

Vetotop CX534 is highly alkaline therefore avoid direct contact with eyes or skin. Vetobond BR434 is latex emulsion. It is recommended to use protective gloves and goggles during application. 

Any skin contact should be washed with plenty amount of water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.

Vetotop CX534 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetodeck UD

Polyurethane based heavy duty, waterproof and UV resistant car park decking system

Vetotop CL530

Premixed 2 to 10 mm thick cementitious self leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed.

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed.

Vetotop EC198

Water Based chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating

view more
Featured Product
Vetoset CA542

Antimicrobial cementitious tile adhesive for health related construction



For use in Hygienic areas such as hospitals, clinics and industrial kitchens.
Laying most types of tile including marble, granite, natural stone, glass mosaic and porcelain.
Tile over tile applications & with heated screeds.
Laying on flexible substrates as well as dry walls (gypsum and cement boards)
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map