Advanced Modified Cementitious Thermal Insulating Plaster
Vetotherm Plaster is blend of OPC, silica sand and graded light weight aggregates plus functional additives for enhancing Workability and adhesion. It can be applied on all surfaces after the proper preparation of the surface. The product provides thermal insulation for building wall sections relying on advanced material technologies.
Vetotherm Plaster is supplied in 20 Kg Bag or Bulk, Coverage ≈ 32 lit wet/20 kg dry bag
Original sealed container of Vetotherm Plaster has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.
Mixing
For manual application add to the mixing container 6.6 - 7.4 liters of water for each 20 Kg bag of Vetotherm Plaster or 33 - 37% of weight for machine application. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
Manual mixing is allowed for small batch quantities, mix for approx. 1-2 min or when homogeneous mix is achieved.
Application
Vetotherm Plaster can be applied in a single or two coats on rough or smooth surfaces by manual or machine application to achieved desired thickness 25-100 mm.
Apply mixed material using spray machine or hawk & trowel technique. Rod or screed to uniform thickness, not exceeding 25 mm for single coat or 25 mm each coat for multiple layers. First layer should be pressed hard against the surface.
For second layer allow the first layer to partially set (60-120min depending on weather). Apply second layer as described above.
Water spray the surface if second layer is carried out next day.
Curing
Vetotherm Plaster is best cured by spraying water evenly on the surfaces of applied materials every 12 hrs for minimum of 3 days. During hot & dry conditions allow curing for minimum of 5 days. It will help to obtain high mechanical strengths.
Surface Preparation
Substrate should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Prior to Vetotherm Plaster, wet the entire surfaces with clean potable water and surface should look damp at the time of Vetotherm Plaster application.
- Do not mix with any additives or products, unless recommended by Saveto.
- Make sure the substrate is suitable for plaster application. In case of doubt, try on sample area to assess its suitability.
- Do not apply the product at temperature less than +5ºC. During summer season the working area must be covered to prevent ill-effects from direct sun and also excessive air-draught during initial curing stage.
- Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically only.
Vetotherm Plaster is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of cold water. Seek medical advise.
For further information, please refer to material safety data sheet.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Advanced modified cementitious thermal insulating plaster
Advanced modified cementitious light weight, thermal insulating masonry mortar
Cementitious based adhesive and base coat for EIFS / ETICS
Cementitious based adhesive and base coat for EIFS / ETICS
Cementitious polymer modified decorative finish coat applied at thicknesses from 1 to 5 mm
Single component acrylic waterproofing membrane