Vetoproof AM763

Single component acrylic waterproofing membrane

Waterproofing of concrete, asbestos, cement and gypsum board surfaces
Protecting spray-PU membranes from UV rays
As a decorative overlay on bituminous membranes and over existing terrazzo tiles
Fast Download
Technical Information
Product Description

Vetoproof AM763 is a single component elastomeric water-based acrylic membrane that has versatile uses for waterproofing in residential and commercial construction. The product is available in a variety of colors.

  • Flexible elastomeric product.
  • Easy to use single component.
  • Weather resistant.
  • Can be applied over sloped roofs.
  • Easy to maintain.
Packaging & Coverage

Vetoproof AM763 supplied in 20 Kg Pails. Theoretical Coverage 0.7-1.0 kg/m2/coat.

Shelf Life & Storage

Original sealed container of Vetoproof AM763 and has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 35ºC.

Application Information
Instructions for use

Vetoproof AM763 can be applied by brush, roll, or airless spray machine. Porous cementitious surfaces should primed with AP443 . The first coat of Vetoproof AM763 should be applied at the rate of 1.5 - 2.0 m²/kg and allowed to cure for 4 - 12 hours depending on ambient temperature.
The second coat should be applied perpendicular to the first coat at the same rate above, and allowed to cure.
For heavy pedestrian traffic, it is recommended to use fiberglass scrim reinforcement, embedded firmly in the second coat while wet, and a third coat should be applied.

Vetoproof AM763 product should be removed from tools, equipment and mixers with clean water prior to the initial set. Cured material can only be removed mechanically.

Surface Preparation

All surfaces should be dry and free from contamination such as oil, grease, loose particles, decayed matter, moss algal growth, laitance, and all traces of mould release oils and curing compounds. This is best achieved by lightly grit-blasting the surface. Where moss, algae or similar growths have occurred, treatment with a proprietary biocide should be carried out after the grit-blasting process. Spalled and deeply disintegrated concrete should be removed to sound concrete and repaired with a Saveto repair system.

Concrete substrates should be at least 14 days old, bituminous substrates should be at least 12 months old  prior to overcoating with Vetoproof AM763.

  • Vetoproof AM763 should not be applied at ambient temperatures below 5°C and dropping.
  • Vetoproof AM763 should not be applied on surfaces expected to suffer form rising dampness or relative humidity greater than 75%.
  • Being Styrene Acrylic; Vetoproof AM763 may yellow over time from UV rays but the integrity and function of the membrane are not compromised
  • If any doubts arise concerning application or substrate conditions, consult Saveto office.
Additional Information
Health & Safety

Vetoproof AM763 contains acrylic polymer which can be harmful to the skin. During use, avoid contact with skin and eyes. Wear suitable protective clothing, gloves, eye protection and respiratory protective equipment. The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. In case of contact with eye, rinse immediately
with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately – do not induce vomiting.

Vetoproof AM763 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.


More Products from this section
Vetoproof CM740

Single component elastomeric crack-bridging cementitious waterproof membrane

Vetoproof AM764

Single component flexible pure acrylic waterproofing membrane

Vetoproof CM744

Polymer modified water resistant cementitious top coat

Vetoproof CM741

Single component penetrating waterproofing system for concrete

Vetoproof CM745

Elastomeric crack-bridging cementitious waterproof membrane

view more
Featured Product
Vetoseal XX772

High efficiency solvent based nonstaining siloxane water repellant

Transforming construction substraes to water repelling surfaces
Cementitious substrates: block and brick work, pre-cast panels and plasters
Sealing and treatment natural stone, marble and absorpent tiles
As a sealer for cementitious based Vetotouch range of EIFS/ETICS finishes
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map