Jordan
Bahrain Egypt Saudi Arabia UAE
EN
EN
Contact news and events About us Home
PRODUCT RANGE
SYSTEM
Selector REFERENCES DOWNLOAD SECTION
Flooring & Coatings Systems
Vetotop UC363

High performance, aromatic & flexible waterproof polyurethane flooring membrane

Uses
Car park decks.
Food and pharmaceutical industry flooring.
Aircraft hangers.
Service centers, workshops.
Fast Download
Technical Data Sheet
download (*.pdf 0.30Mb)
Method Statement
download (*.pdf 0.21Mb)
MSDS
download (*.pdf 0.29Mb)
Technical Information
Product Description

Vetotop UC363 is a two component, solvent free aromatic polyurethane intermediate coat and waterproofing membrane. The product needs to be overcoated with Vetotop UC370 or Vetotop UC371 for optimum performance and scratch resistance. The products flexibility enables it to perform in a wide range of flooring applications.

Advantages
  • Fast easy application
  • Flexible.
  • Low maintenance cost.
  • Hygienic, impervious and easily cleanable.
  • High bond, stronger than concrete cohesive strength.
  • Excellent impact resistance.
Compliance Standard
  • ASTM D 6577-15
  • BS EN476:2009 as class 1 in flame spread.
Packaging & Coverage

Vetotop UC363 is supplied in 4 or 15 Liter Kits with Theoretical coverage :1.25 m2 / Liter

Vetoprime UP360 is supplied in 4  Liter Kits with Theoretical coverage: 8-10 m2 / Liter

Vetoprime EP490 is supplied in 4  Liter Kits with Theoretical coverage: 8-10 m2 / Liter

Shelf Life & Storage

Original sealed kit of Vetotop UC363 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.

Application Information
Instructions for use

Priming
Concrete substrates shall be primed with Vetoprime UP360 or Vetoprime EP490.

Mixing Vetotop UC363
In a separate mixing vessel, use a slow speed mixer to mix the base, hardener for 3 minutes. Mix these components in the quantities supplied taking care to ensure all containers are scraped clean. Do not add solvent thinners at any time.

Application
Apply Vetotop UC363 by a pin leveler or airless spray to the dry surface. The application should be at a rate of 1.25 m2/litre per coat.
Application should not be carried out when relativehumidity exceeds 75%, or when the surface temperature to be coated is less than 3°C above the dew point.
Vetotop UC363 can be applied as a single coat, or dressed with Vetograin products to give a slip resistant finish.
For more information, please refere to Vetograin Technical Data Sheet.

Expansion Joints
Expansion joints in the existing substrate must be retained and continued through the Vetotop UC363 topping. Saveto have a range of joint sealants specifically designed for flooring (see Vetoflex PU781, and Vetoflex PS782 product data sheets).

Cleaning
Tools and equipment should be cleaned with Vetonit Solvent XX300 immediately after use.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc. Laitence and weak surface layer shall be removed using mechanical methods such as grinding or blasting in order to provide a sound well profiled surface. All necessary repairs should be made prior to application by using epoxy mortar from Vetorep ER range. New concrete floors shall be at least 28 days old with moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).

Additional Information
Health & Safety

Vetotop UC363 is irritant and harmful therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. In case of contact with eyes, clean immediately with plenty of clean cold water and seek medical advise.
Ensure adequate ventilation when using product or when using solvent for cleaning purposes and avoid inhalation of vapours. The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medial advice. If swallowed, seek medical attention immediately - Do not induce vomiting.
Vetonit Solvent XX300 is flammable. Keep away from sources of ignition. No Smoking. In the event of fire extinguish with CO2 or foam. Refer to product(s) MSDS for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetodeck UD

Polyurethane based heavy duty, waterproof and UV resistant car park decking system

Vetotop CL530

Premixed 2 to 10 mm thick cementitious self leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed.

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed.

Vetotop EC198

Water Based chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating

view more
Featured Product
Vetonit Ultra

Polymer modified weather resistant multipurpose adhesive for tiles.

 

Uses
For Ceramic tiles, natural stone conglomerates (Granite & Marble, Terrazo) , artificial stone and large format tiles.
Tiling on smooth concrete surfaces, lightweight bricks, blocks, plaster boards.
Tiling on wall surfaces that are plastered with water resistant plasters such as Vetonit Render & Vetonit Base WR on damp concrete interiors.
Suitable for dry & wet conditions.
Suitable for tile on existing tile applications.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map
Home
About us
news and events
Contact
DOWNLOAD SECTION
REFERENCES
Copyright ©2015-2016 Saudi Vetonit Co. Ltd. All Rights Reserved.