Renders & Finishes
Vetonit Base WR EG

Weather Resistant Premix Cement Coating for External Use

Can be applied externally onto walls & other surfaces subjected from dry to humid conditions
Suitable for applications on concrete surfaces and precast concrete surfaces.
On wall surfaces that are plastered with water resistant plasters, Vetonit Renders and on damp concrete interiors.
Fast Download
Technical Information
Product Description

Vetonit Base WR EG is a cement based coat composed of hydraulic binders, selected aggregates and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which required only addition of clean water to produce easily workable mortar. Vetonit Base WR EG is a high quality product for multipurpose use and as a base coat for Vetonit Finish WR EG. Vetonit Base WR EG can be applied in thickness from 1 mm to 5 mm, in one or two layers depending on site requirement. Vetonit Base WR EG is available in two standard colours, white, grey & Saveto standard colours.

  • Factory controlled pre-blend ensures consistent high quality.
  • Requires only addition of water on-site at the time of usage.
  • Manual or spray machine application.
  • Superior workability.
  • Easy application that enables high Productivity.
  • Excellent Adhesion on variety of substrates.
  • Water/weather resistant.
  • Suitable for humid & dry conditions.
  • Suitable for walls & precast surfaces.
  • Guards the surfaces from rain & natural condensations.
Compliance Standard
  • BS:EN 1015
  • ASTM C348 
  • ASTM C109
  • BSEN 998-1
  • BS:EN 413-2 
Packaging & Coverage

Vetonit Base WR EG is supplied in 25kg Bag or Bulk, with Yield: 1.0 - 1.2 Kg /m2 / 1mm thickness

Shelf Life & Storage

Original sealed bag of Vetonit Base WR EG has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place.
Vetonit Base WR EG is non-flammable.

White, Grey & coloured Powder
Application Information
Instructions for use

Internal Block Walls & Rough Surfaces
For manual application add to the mixing container 7.5-8.5 litres of water for each 25 Kg bag of Vetonit Base WR EG. For Spray machine application use 9.5-10.0 litres of water for each 25 kg bag. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved. Allow the mixed material to stand for about 10 minutes and remix briefly with no further water should be added.

Smooth Concrete Surfaces
Add 0.5 litres of Vetonit Bond 2 to the mixing water and adjust the water requirement accordingly for each 25 kg bag. Follow same mixing procedure as described above.
Mixed material can be used within 2 hours. Do not add water to the mix once the mixed mortar start to harden.

Vetonit Base WR EG can be applied in one or two layers as required to achieve desired thickness of 1-5 mm.
Various grades of finish textures can be obtained by selecting appropriate spray machine nozzle sizes.
Allow the installed application to remain undisturbed for at least 48 hours.

Vetonit Base WR EG is best cured by spraying water on the surfaces of applied materials every 12 hrs for minimum of 3 days. During hot & dry conditions allow curing for minimum of 5 days. This will help in achieving uniform colour, minimize risk of surface cracks and high mechanical strengths.

Surface Preparation

The surface should be sound, clean free from loose material, grease, laitance, dirt curing compound, etc.
Prior to Vetonit Base WR EG application, wet the entire surfaces with clean potable water and surface should look damp at the time of Vetonit Base WR EG application.

  • Do not mix with any additives or products, unless recommended by Saveto.
  • Make sure the substrate is suitable for plaster coat application. In case of doubt, try on sample area to assess its suitability.
  • Do not apply the product at temperature less than +5ºC. During summer season the working area must be covered to prevent ill-effects from direct sun and also excessive air-draught during initial curing stage.
  • Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically only.
  • For further information contact our technical department.
Additional Information
Health & Safety

Vetonit Base WR EG is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately washed with copious amount of clean cold water. Seek medical advise.
For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetonit Crack Filler

High quality premixed surface crack filler


Water resistant internal use premix smooth cement coating


Water resistant external use premix smooth cement coating

Vetonit Gypsum Joint Compound

Premium quality premixed compound for gypsum board joints

Vetonit Putty WR

Water resistant high quality premixed putty

view more
Featured Product
Vetotop EC493

Solvent based high performance, self priming, thin epoxy topping

Floor and wall coating for a variety of industrial applications such as: production assembly areas, workshops, dairies, bottling plants, breweries, kitchens, showrooms, etc.
As a sealer for Vetotop CL and XT ranges
Wet working areas subject to chemical spillage
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map