High performance aliphatic acrylic protective & decorative coating for concrete and masonry
Vetotop AC442 comprises a single component penetrating silane-siloxane primer and a single component pigmented coating, both ready for immediate site use. Vetoprime AP443 Is supplied as a clear liquid and is based on a silane-siloxane dissolved in a penetrating organic carrier. Vetoprime AP443 is reactive and capable of producing a chemically-bound hydrophobic barrier, thus inhibiting the passage of water and water- borne contaminants. Vetotop AC442 is an aliphatic acrylate, solvent based protective coating, providing outstanding resistance to aggressive elements, UV light and rain. It is available in a wide range of colours.
Vetotop AC442 is supplied in 20 Kg Bucket with consumption: 0.2 k/m2 per coat
Original sealed buckets of Vetotop AC442 and Vetoprime AP443 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.
The coating should be applied in two coats to achieve a total dry film thickness of not less than 150 microns. To achieve the correct protective properties, Vetotop AC442 system must be applied on to the substrate at the coverage rates recommended.
In order to obtain the protective properties of the Vetotop AC442 system, it is important that the correct rates of application and over-coating times are observed. please refer to saveto TDS to obtain the rates.
Application should not commence if the temperature of the substrate is below 2°C or above 40°C.
Any areas of glass should be masked. Plants, grass, joint sealants, asphalt and bitumen-painted areas should be protected during application.
Vetoprime AP443 should be applied in one or more coats until the recommended application rate of 0.4 liter per square meter has been achieved. This is best accomplished by using portable spray equipment of the knapsack-type. If in doubt about the condition of the substrate, Saveto Technical Center should be consulted.
The primer should be allowed to dry for a minimum of two hours (at 20°C) and 1 hour (at 35°C) before application of Vetotop AC442. Under no circumstances should the primer be over-coated until the surface is properly dry.
Vetotop AC442 may be applied by the use of suitable brushes or rollers. Queries relating to spray application should be referred to Saveto Technical Department prior to the commencement of work.
All primed substrates should be treated with two coats of Vetotop AC442. The material should be stirred thoroughly before use. The first coat should be applied to all areas by the use of suitable brushes or rollers to achieve a uniform coating with a wet film thickness not less than 175 microns and not greater than 225 microns. This coat should be allowed to dry before continuing.
The second coat of Vetotop AC442 should be applied exactly as detailed above, again achieving a wet film thickness not less than 175 microns and not greater than 225 microns.
Vetorep CR523 should be removed from tools and equipment with clean water immediately after use. Vetoprime AP443 and Vetotop AC442 should be removed from tools and equipment using Vetonit Solvent XX400.
All surfaces should be dry and free from contamination such as oil, grease, loose particles, decayed matter, moss, algal growth, laitance, and all traces of mould release oils and curing compounds. This is best achieved by lightly grit blasting the surface. Where moss, algae or similar growths have occurred, treatment with a proprietary biocide should be carried out after the grit-blasting process.
Where application over existing sound coatings is required, trials should be conducted to ensure compatibility and retention of the bond between the underlying coating and the substrate.
It is essential to produce an unbroken coating of Vetotop AC442. To ensure this is achieved, surfaces containing blow- holes or similar areas of pitting should first be filled using Vetorep CR523, a cementitious fairing coat. Vetorep CR523 should be allowed to cure for approximately 48 hours dependent on ambient conditions before the application of Vetotop AC442.
Vetorep CR523 contains cement powders which, when mixed or become damp, release alkalis which can be harmful to the skin. During use, avoid inhalation of dust and contact with skin and eyes. Wear suitable protective clothing, gloves, eye protection and respiratory protective equipment. The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately - do not induce vomiting.
Vetoprime AP443, and Vetonit Solvent XX400 should not come in contact with the skin and eyes, or be swallowed. Ensure adequate ventilation and avoid inhalation of vapours.
Some people are sensitive to resins, hardeners and solvents. Wear suitable protective clothing, gloves and eye protection. If working in confined areas, suitable respiratory protective equipment must be used. The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately - do not induce vomiting.
Vetorep CR523 is non-flammable. Vetoprime AC443, and Vetonit Solvent XX400 are flammable. Keep away from sources of ignition. No smoking. In the event of fire, extinguish with CO2 or foam. Do not use a water jet.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Polyurethane based heavy duty, waterproof and UV resistant car park decking system
Premixed 2 to 10 mm thick cementitious self leveling underlayment
Premixed 10 to 30 mm thick cementitious screed.
Premixed 30 to 100 mm thick cementitious screed.
Water Based chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating
Non-metallic colored dry-shake monolithic floor hardener for stamped concrete