Concrete Grouts, Repairs, & Enhancements
Vetorep ER430

Pitch extended epoxy based repair compound for asphalt crack repairs

Repair of asphalt cracks in highways, aprons and pavements.
Reinstate asphalt integrity while maintaining flexibility.
Road bridges, helicopter decks, work platforms, car parks, walkway, wet work industrial areas and cargo handling areas
Fast Download
Technical Data Sheet
download (*.pdf 0.23Mb)
Method Statement
download (*.pdf 0.21Mb)
Technical Information
Product Description

Vetorep ER430 is a two component epoxy based thixotropic solvent free and fast strength development flexible repair compound. Once components of the kit are mixed the products becomes abrasion resistant that can be poured into asphalt cracks where it sets and bonds perfectly to the asphalt substrate

  • Rapid strength development.
  • Chemically resistant.
  • Superior bond to a wide range of substrates.
  • Compatible with most line marking coatings.
  • Abrasion resistant for heavy duty applications.
  • Cures in damp conditions.
Compliance Standard
  • EN 13062:2003
  • EN 1504:2013
  • EN1992:2006
Packaging & Coverage

Vetorep ER430 is supplied in 5 liters Kits

Vetonit Solvent XX400 is supplied in 5 liters Cans.

Shelf Life & Storage

Original sealed kits of Vetorep ER430 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded temperature controlled place <25ºC.

Application Information
Instructions for use

Care should be taken to ensure that Vetorep ER430 is thoroughly mixed to produce a fully homogeneous flowable mortar. Vetorep ER430 must be mixed mechanically. The ‘hardener’ and ‘base’ components must be stirred thoroughly to disperse any settlement before mixing them together. The entire contents of the ‘hardener’ container should then be emptied into the ‘base’ container and thoroughly mixed for 3 minutes, then emptied into a forced action mixer of adequate capacity. Add the aggregate slowly with the mixer running and continue for 2 to 3 minutes until all the components are thoroughly blended. Under no circumstances should part packs be used. A slow speed heavy duty drill fitted with a purpose mixer can be facilitated.

Pour the mixed Vetorep ER430 to the prepared substrate till the cracks are filled completely into place. Allow the material to set for 16 hours at 25ºC prior to allowing foot traffic and 48 hours prior to allowing heavy traffic. In case of ambient temperature of 35ºC vehicular traffic can be allowed at 30 hours.

Low temperature working
Vetorep ER430 can be applied in cold conditions down to 12ºC. The materials should not be applied when the substrate and/or air temperature is 12ºC and falling. At 12ºC static temperature or at 12ºC and rising, the application may proceed.
However it is highly recommended to apply the products at temperatures above 15ºC to dismiss practical impediments of application.

High temperature working
At ambient temperatures above 35ºC Vetorep ER430 will have shorter pot life. The materials should be stored in the shade or in an air- conditioned environment and should not be applied in direct sunlight.

Vetorep ER430 should be removed from tools, equipment and mixers with Vetonit Solvent XX400 immediately after use.

Surface Preparation

Clean the surface and remove any loose particles, use compressed air for effective cleaning. 


Vetorep ER430 should not be used when the temperature is below 10ºC and falling. Do not mix part packs under any circumstances. If any doubt arises concerning temperature or substrate condition, consult the local Saveto office.

Additional Information
Health & Safety

Vetonit Solvent XX400 and Vetorep ER430 should not come into contact with the skin, eyes or be swallowed. When using ensure adequate ventilation and avoid inhalation of vapor. Some people are sensitive to resins, hardeners and solvent. Wear suitable protective clothing, gloves, and eye protection. The use of barrier creams provides additional skin protection. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical attention immediately. If swallowed seek medical attention immediately. Do not induce vomiting.
Vetorep ER430 is non-flammable. Vetonit Solvent XX400 are flammable. Keep away from sources of ignition. No smoking. In the event of fire, extinguish with CO2 or foam. Do not use a water jet.
For further information, refer to the Product Material Safety Data Sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor EG346

Epoxy resin twin cartridge anchoring grout

vetoanchor PG347

Polyester injection and anchoring grout

Vetocure XT425

Water based concrete curing compound

Vetocure XT426

Multi-Purpose Acrylic Resin Curing Compound

Vetocure XT427

Water based acrylic curing compound and primer *

view more
Featured Product
Acoustic Plaster

High quality light weight premixed acoustic plaster

Theaters and auditoriums
Media and recording studios
Boiler, chiller and machine rooms
Where sound dampening is required
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map