Concrete Grouts, Repairs, & Enhancements
Vetocure XT427

Water based acrylic curing compound and primer *

As a spray applied membrane for interior application on concrete surfaces and renders.
In situations where the surfaces needs to be painted or plastered.
Fast Download
Technical Data Sheet
download (*.pdf 0.12Mb)
Method Statement
download (*.pdf 0.21Mb)
Technical Information
Product Description
  • Improved curing of concrete, enhances cement hydration and provides a more durable concrete.
  • Control of moisture loss
  • Improved surface quality
  • Reduced permeability.
  • Minimised potential for surface cracking and shrinkage.
  • Compatible with many after trade applications.
  • Easy application reduces labour costs.
Compliance Standard
  • ASTM C309
  • AASHTO M148 as Type 1D
Packaging & Coverage

Vetocure XT427 I=is supplied in 20 Pail & 200 liter Drum, Coverage: 4 - 6 m2/Liter

Stated consumptions data are for general guidance. Actual consumption depends on the nature of substrate, method of application and wastage.

Shelf Life & Storage

Vetocure XT427 has a minimum shelf life of 12 months, provided the temperature is kept within the range of 5ºC to 35ºC. Freezing and prolonged exposure to heat or direct sunlight should be avoided. Should the temperature of the product fall outside this range then Saveto Technical Service Department should be contacted for advice.
Containers should be kept sealed and airtight to prevent loss of moisture by evaporation.

Application Information
Instructions for use

Application to fresh concret
Vetucure XT427 should be spray applied to the surface of fresh concrete. Application should be made approximately 30 minutes after evaporation has left the concrete free from surface water.
Spray machine producing a fine mist may be used for Vetocure XT427 application, such as knapsack or motorised sprayers. The suitability of the machine should be ensured by an application trial. The spray nozzle should be held approximately 450 mm from the concrete surface and passed back and forth to ensure complete coverage. Pump pressure should be maintained to give an even, fine spray.
To ensure continued curing, no further application of water or other material is necessary after application. The cured surface should not be disturbed until it has sufficient strength to bear surface loads. The applied film should not be waked on before it is fully dry and care should be taken to ensure that the film is not broken.

Application to hardened concrete
Vetucure XT427 can be applied manually if spray machine is not available. Use soft brush, broom or wide roller for applying Vetocure XT427. Application in this manner should only be made once the concrete has hardened sufficiently to not be damaged during application.
Vetocure XT427 may also be applied to the surface of newly hardened concrete immediately after de-moulding. The surface must be structurally sound, free from oil, grease and other forms of contamination. which may otherwise prevent adhesion of Vetocure XT247 to the concrete.
The recommended coverage rate for Vetocure XT427 is between 4.0 and 6.0 m2 / litrer (0.17 - 0.25 litres/m2 ).

Over-coating and removal
Vetocure XT427 can be applied over old, covered substrates. Small trial area is recommended to ensure that the desired properties are obtained.
Before over-coating with Vetocure XT427, ensure that the surface is completely free of stains, oils and other materials that may interfere with the adhesion of the material.

* Important Note
Consult your Saveto technical representative for conditions and application method.

Spray equipment should be cleaned immediately after use by flushing through with water.

Additional Information
Health & Safety

Vetocure XT427 does not fall into the hazard classifications of current regulations. However, it should not be swallowed or allowed to come into contact with skin and eyes either in bulk or spray form.
Suitable protective gloves and goggles should be worn. Splashes on the skin should be removed with water. In case of contact with eyes rinse immediately with plenty of water and seek medical advice. If swallowed seek medical attention immediately - do not induce vomiting.
Vetocure XT427 is non - flammable.
For further information consult the Material Safety Data sheet available for this product.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor EG346

Epoxy resin twin cartridge anchoring grout

vetoanchor PG347

Polyester injection and anchoring grout

Vetocure XT425

Water based concrete curing compound

Vetocure XT426

Multi-Purpose Acrylic Resin Curing Compound

Vetogrout CG510

Multipurpose universal cementitious non-shrink grout

view more
Featured Product
Vetonit PCM

Saveto plaster accessories - plaster corner mesh lath 


At inside corner joints with dissimilar material base.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map