Vetoproof UM765

Pitch-modified elastomeric polyurethane liquid applied waterproofing membrane

Wet areas: kitchens, bathrooms, swimming pools, etc.
Basements, tunnels, subways and culverts
Inveted roofs, suspended slabs, balconies
Tanking systems
Fast Download
Technical Information
Product Description

Vetoproof UM765 is a premium quality pitch extended polyurethane waterproofing membrane, the product is liquid applied that hardens through reaction with atmospheric water vapour to form a highly elastic rubbery jointless membrane that is resistant to aggressive ground water and sewage. Vetoproof UM765 can be applied at 0.5mm on vertical application.

  • Easy to apply single component liquid application
  • Jointless application that is easy to detail
  • Crack bridging highly elastic membrane at various temperatures
  • Vapour proof
  • Easy to repair and maintain
  • Fully bonded prohibiting lateral migration of water
  • Thermally and chemically stable, resistant to oxidation and embrittlement
Compliance Standard

- ASTM C836/C836M (2012)

- ASTM C1417/C1417M-05 (2014) e1

- ASTM C898/898M-2009

Packaging & Coverage

Vetoproof UM765 is supplied in 20 Liters Pails 
Theoretical Coverage: 2m²/L @ 0.5mm thickness

Shelf Life & Storage

Original sealed pail of Vetoproof UM765 has a shelf life of 6 months provided it is stored in original sealed containers clear of ground in a dry and shaded place below 35ºC.

Application Information
Instructions for use

Design Criteria

Vetoproof UM765 use follows the guidelines of EN BS8102:2009 and CIRIA report No. 139 and ASTM guides C1417 nad 898.


Priming is not usually required on good quality concrete substrates. However, for highly porous or absorbent concrete use use Vetoseal XX777-50.


Vetoproof UM765 should be applied by brush, trowel or a gaged spreader at a thickness of 0.5mm. Glass fiber scrim and joint tapes can be used on corners and critical areas for reinforcement of the membrane.
Tiling over Vetoproof UM765 is possible, in such cases sharp sand needs to be sprayed over Vetoproof UM765 while still wet, 24 hours later all excess sand is to be removed and a suitable tile adhesive from Saveto range can be used to bond the tiles directly over the membrane.


Vetoproof UM765 must be allowed to cure for a minimum of 24 hours prior to placing protection. Where damage to the membrane is possible; the membrane needs to be protected by a cementitious screed or protection boards.
Note: Vetoproof UM765 is not resistant to UV light.


All tools employed for the application of Vetoproof UM765 can be cleaned with Vetonit Solvent XX400 before it hardens otherwise mechanical means are needed.

Surface Preparation

All surfaces where Vetoproof UM765 has to be applied must be clean and have an open capillary system. Eliminate laitance, dirt, grease and other loose materials by means of high pressure water jetting or wet sand blasting. Defective concretes such as cracks and honeycombs, etc. has to be chased out and repaired prior to the application.

Additional Information
Health & Safety

Some people are sensitive to resins, hardeners and solvents. Wear suitable protective clothing, gloves, and eye protection. If working in confined areas, suitable respiratory protective equipment must be used. The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medial advice. If swallowed, seek medical attention immediately - Do not induce vomiting.

Vetoproof UM765 is flammable, do not use near to open flames. Refer to product MSDS for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoproof AM763

Single component acrylic waterproofing membrane

Vetoproof CM740

Single component elastomeric crack-bridging cementitious waterproof membrane

Vetoproof AM764

Single component flexible pure acrylic waterproofing membrane

Vetoproof CM744

Polymer modified water resistant cementitious top coat

Vetoproof CM741

Single component penetrating waterproofing system for concrete

view more
Featured Product
Vetotop EL392

Industrial grade self smoothening epoxy based floor topping from 0.8 to 2 mm thickness

Industrial kitchens and food processing plants
Heavy duty vehicle factories, car parks and aircraft hangers
Clean rooms, battery rooms and laboratories
Any flooring were impact resistance is of importance
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map