Concrete Grouts, Repairs, & Enhancements
Vetogrout CG510

Multipurpose universal cementitious non-shrink grout

Grouting & anchoring structural steel and precast concrete members
Filling voids & tie-rod holes
Under-plate grouting & light machine beds
Anchoring a wide range of fixings such as anchor bolts, stanchion bases, masts and fence posts
Fast Download
Technical Information
Product Description


  • Factory controlled pre-blend ensures consistent high quality
  • Requires only addition of water on-site at the time of usage
  • Chloride free, High early & ultimate strength and low permeability ensure the durability of the hardened grout
  • High physical and mechanical properties
  • Non-shrink characteristics
  • Gaseous expansion system compensates for shrinkage and settlement in the plastic state
Compliance Standard

- ASTM C1107/1107M-14 (previously CRD621) as Grade A.

- ASTM C938-10

- Sampling as per ASTM C943

- EN 934: 2012 (testing as per EN480, EN 13395)

Packaging & Coverage

Vetogrout CG510 supplied in 25 kg Bag. Yield - 13 Liters.

Shelf Life & Storage

Original sealed bag of Vetogrout CG510 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place at temperatures between +5ºC - 35ºC..

Application Information
Instructions for use

For best results a mechanically powered grout mixer should be used. When quantities up to 50 kg are used, a slow speed drill fitted with a high shear mixer is suitable. Larger quantities will require a high shear vane mixer. Do not use a colloidal impeller mixer.
To enable the grouting operation to be carried out continuously, it essential that sufficient mixing capacity and labor are available. The use of a grout holding tank with provision to gently agitate the grout may be required.
The quantity of clean water required to be added to a 25 kg bag to achieve the desired consistency is:
Trowellable 3 - 3.25 Liters
Flowable 3.5 - 3.75 Liters
Fluid 4 - 4.5 LitersThe selected water content should be accurately measured into the mixer. The total contents of the Vetogrout CG510 bag should be slowly added and continuous mixing should take place for 5 minutes. This will ensure that the grout has a smooth even consistency.

At 25ºC place the grout within 20 minutes of mixing to gain full benefit of the expansion process.
Vetogrout CG510 can be placed in thicknesses up to 100 mm in a single pour when used as an under-plate grout. For thicker sections it is necessary to fill out Vetogrout CG510 with well-graded silt free aggregate to minimize heat build-up. Typically a 10 mm aggregate is suitable. Any bolt pockets must be grouted prior to grouting between the substrate and the base plate.
Continuous grout flow is essential. Sufficient grout must be prepared before starting. The time taken to pour a batch must be regulated to the time to prepare the next one.


On completion of the grouting process, exposed areas should be covered well with polyethylene sheets to prevent evaporation of the water in the mix at least for the first 24 hours, later the grouted area should be cured using clean potable water twice a day for 3 days. Or you can use Vetocure XT425 water based curing compound after placing the grout.

Vetogrout CG510should be removed from tools and equipment with clean water immediately after use. Cured material can be removed mechanically.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.

Wet the substrate to achieve a saturated and surface dry condition prior to application of Vetogrout CG510. Erect hopper system and form-work, make sure that the shuttering is watertight by use of a polyurethane sealant such as Vetofl ex PU780 or a rubber gasket seal. This step is important to insure no cement paste and water leak from the shuttering. Contact your Saveto’s local representative for more technical information, Saveto’s grouting detailed method statement, and CAD details

It is essential that the base plate is clean and free from oil, grease or scale. Air pressure relief holes should be provided to allow venting of any isolated high spots.

If leveling shims are used and are to be removed after the grout has hardened, they should be treated with a thin layer of grease.

Unrestrained Surface Area
Generally the gap width between the perimeter form-work and the plate edge should not exceed 150 mm on the pouring side and 50 mm on the opposite side. It is advisable where practical to have no gap at the flank sides.

Additional Information
Health & Safety

Vetogrout CG510 is alkaline and should not come into contact with skin and eyes. Avoid inhalation of dust during mixing. Gloves, goggles and dust mask should be worn. If contact with skin occurs, wash with water. Splashes to eyes should be washed immediately with plenty of clean water and medical advice sought.

Vetogrout CG510 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor EG346

Epoxy resin twin cartridge anchoring grout

vetoanchor PG347

Polyester injection and anchoring grout

Vetocure XT425

Water based concrete curing compound

Vetocure XT426

Multi-Purpose Acrylic Resin Curing Compound

Vetocure XT427

Water based acrylic curing compound and primer *

view more
Featured Product
Vetobond AB432

Acrylic polymer cement modifier & bonding agent

Enhancement of renders, floor toppings and plasters
As a primer for bonding cementitious repair materials (Vetorep range of products)
As a primer for renders and plasters on fairfaced concrete and gypsum boards
As a curing membrane, ready to receive further cementitious renders by re-priming
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map