Concrete Grouts, Repairs, & Enhancements
Vetogrout CG513

Free-flowing pre-baged non-shrink cementitious cable grout

Grouting of anchor cables in suspended bridges
Grouting of anchors in post tensioning cases
Soil stabilization grouting and micro-grouting
Cavity infill under foundations and grade slabs
Fast Download
Technical Information
Product Description

Vetogrout CG513 is a single component cementitious grout composed of blended cements, special additives and fillers to enable fluid consistency and smooth free flow of grout in demanding anchoring and post tensioning applications. The product once mixed with the designated amount of water will form a fluid grout that is either pourable or pumpable through small openings to long distances using Saveto recommended grout pumping equipment.

  • Free flow characteristics
  • Non-Shrink with high adhesion
  • Low coefficient of thermal expansion
  • Hydrogen and chloride free
  • Tropical formulation suitable for MENA conditions
  • High ultimate and early strength
  • Suitable for grouting post tensioned cables and anchors
  • Contains migratory corrosion inhibitors to protect stressed steel cables and anchors
Compliance Standard

- ASTM C938-10

- ASTM C1741 (Testing of post tensioning tendon grout)

- EN 1992

- EN 447

Packaging & Coverage

Vetogrout CG513 supplied in 25 Kg Bag.

Consumption around to 16.87 Liters Yield.

Shelf Life & Storage

Original sealed kits of Vetogrout CG513 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place.

Application Information
Instructions for use

Measure and pour 7.5 to 8.25 liters of clean water to a suitable sized bucket, then slowly add the powder of one full bag of 25 kg size to the bucket while mixing using a slow speed mixer fitted with a suitable mixing paddle. Continue mixing for an additional 3 minutes till a uniform lump free consistency is reached.
Allow the grout to mature for 1 minutes prior to pouring, for larger quantities it is recommended to use a pan forced action mixer, do not use free fall mixers.
Place Vetogrout CG513 by pouring into designated application area in a continuous manner and do not allow air pockets to develop. The pouring should be within a maximum of 20 minutes after mixing.
Where grout pumps are used for duct grouting, it is recommended to place the whose as deep as possible into the duct, start the pumping process and then slowly retract the hose insuring that pumped material is pushing the air out of duct.

Vetogrout CG513 should be removed from tools and equipment with Vetonit Solvent XX400 immediately after use. Cured material can be removed mechanically.

Surface Preparation

The area / duct to be grouted shall be cleaned with water before the application of Vetogrout CG513. Any free water must be drained.

Additional Information
Health & Safety

Vetogrout CG513 Contains reins which may cause sensitization by skin contact. Avoid contact with skin and eyes and inhalation of vapor. Wear suitable protective clothing, gloves and eye/face protection. Barrier creams provide additional skin protection. Should accidental skin contact occur, remove immediately with a resin removing cream, followed by soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed seek medical attention immediately. Do not induce vomiting.

Vetogrout CG513 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor EG346

Epoxy resin twin cartridge anchoring grout

vetoanchor PG347

Polyester injection and anchoring grout

Vetocure XT425

Water based concrete curing compound

Vetocure XT426

Multi-Purpose Acrylic Resin Curing Compound

Vetocure XT427

Water based acrylic curing compound and primer *

view more
Featured Product
Vetonit Crack Filler

High quality premixed surface crack filler

Filling static cracks up to 4 mm, blow holes and minor undulations etc.
Applied externally & internally in wet to dry conditions onto the walls & ceilings such as Bathrooms & Kitchens.
On concrete and plastered surfaces that are smooth and also precast concrete surfaces.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map