Primers and Ancillary
Vetobond PB436

Polymeric soil stabilizer

Sand stabilization in embankments, runways and sand dunes.
Dust prevention & erosion control.
Rural walk-ways and paths.
Open desert sand stabilization and sand storm inhibition.
Landscaping applications.
Fast Download
Technical Data Sheet
download (*.pdf 0.14Mb)
Method Statement
download (*.pdf 0.14Mb)
Technical Information
Product Description

Vetobond PB436 is a modified styrene acrylate copolymer emulsion which is supplied as a ready to use white milky liquid. It is designed to resist hydrolysiand stabilize soil for various requirements such as the open desert, areas surrounding aircraft runways and highways, construction sites, military depots,...etc.

  • Factory controlled single component easy to use and easily gaged.
  • Water emulsified, environment friendly product.
  • Odorless and non flammable.
  • Resistant to hydrolysis.
  • Improves soild bearing strength.
  • Chloride free.
  • Improves freeze-thaw resistance.
Packaging & Coverage

Vetobond PB436 supplied in 20, 200 Liter containers
Coverage - As required

Shelf Life & Storage

Original sealed container of Vetobond PB436 has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 35ºC.

Milky liquid
Application Information
Instructions for use

Design Criteria

Vetobond PB436 is designed to withstand tropical middle east and north africa climate conditions. The product is ready to use and can be diluted up to 1:2 with potable water depending on application conditions. Vetobond PB436 application and dilution rates vary depending on required use 

Dilution & Application

Vetobond PB436 can be diluted by volume up to 1:50 with potable water, for general use purposes the recomended dulution is 1:6 with potable clean water with a maximum solids content of 20,000 ppm of mineral salts.
Use mechanical means to dilute the product such as a slow speed mixer (400 to 500 RPM) fited with a suitable mixing paddle to ensure proper dispersion of the product once diluted with water. The application of Vetobond PB436 is by iterative flooding of the substrate using spray equipment of suitable nature to the size of application. Subsequent coats (passes) are made once the first coat has been absorbed by the substrate, generally 2 to 3 flood coats are recomended. The coverage rates vary depending on use and type of soil to be stabilized.

Surface Preparation

For best results, substrates to be treated need to be compacted to the engineers required levels and intended use standards prior to application of Vetobond PB436.

Additional Information
Health & Safety

Though Vetobond is not classified as hazardous, some people may be sensetive to acrylic based polymers.
Wear suitable protective clothing, gloves, eye protection and respiratory protective equipment. The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. In case of contact with eye, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately – do not induce vomiting.
Vetobond PB436 is not flamable.
Refer to Material Safety Data Sheet for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Ready Mix Bond

Multi-purpose bonding agent & admixture

Saveto Bond 2

Multipurpose low viscosity bonding agent & admixture

Vetobond PB434

Polymeric bonding agent, waterproof mix enhancer & primer

Vetobond PB433

Versatile resin adhesive, cement modifier, bonding agent & sealer

Vetobond EB430

Solvent free epoxy bonding agent to bond old to new concrete

view more
Featured Product
Vetogrout UR710

Hydro-reactive foaming flexible polyurethane injection resin.

Stopping crack seeping water.
Injection of structural elements in water retaining or water excluding structures.
Crack injection to stop water flow in retaining walls, manholes, reservoirs,...etc.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map