Concrete Grouts, Repairs, & Enhancements
Vetorel XT422

Chemical mold and form-work release Concentrate

Vetorel XT422 is used after dilution for the treatment of wooden and metal form work or molds prior to the casting of concrete to facilitate form stripping
Minimizing concrete surface blemishes and pinholes
Fast Download
Technical Data Sheet
download (*.pdf 0.16Mb)
Method Statement
download (*.pdf 0.23Mb)
Technical Information
Product Description

Vetorel XT422 is a single component, black box concentrate of specially formulated oils and additives that when diluted by 200 liters of diesel oil will produce a low viscosity liquid composed of synthetic mineral oils and special varied additives that performs in a superior manner to standard oil based mold release agents. Vetorel XT421 provides the plywood surface with a water repellent film preventing concrete from adhering to the form work resulting with a smooth, stainless concrete surface.

  • Minimizes storage requirement of conventional release agent products
  • Stainless fairfaced concrete finish
  • Ensures easy release reducing damage to molds and form-work
  • Produces neat concrete surfaces by letting the air & water bubbles rise freely during vibration
  • Performs all wooden or plywood form surfaces, GRC as well as to synthetic or steel forms
  • Extend usable life of shuttering
Packaging & Coverage

Vetorel XT422 supplied in 7 Kg. Theoretical Coverage: 7 - 30 m2/Ltr of diluted product.

Shelf Life & Storage

Original sealed container of Vetorel XT422 and has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 35ºC.

Application Information
Instructions for use


Pour the entire contents of the Vetorel XT422 concentrate into a 200 liter drum of diesel oil.

Use a drum stirrer or a small circulation pump to mix the contents of the drum.


Vetorel XT422 is supplied in 10 kg pails that need to be mixed and diluted with 200 liters of Diesel prior to use. The mix can then be applied by brush, roller or spraying machine.

Apply the diluted Vetorel XT422 on plywood or steel shutter before the first casting. After every use of form-work, the shutter should be recoated lightly with Vetorel XT422 dilute.

Do not over apply the diluted Vetorel XT422 on the form-work. Excessive material should be allowed to drain before using the form-work.

Apply the product with a brush or preferably with a sprayer. For best results, it is advisable to apply diluted Vetorel XT422 at least two hours before using the shutter.

Consult Saveto technical department for any additional information.

Surface Preparation

All molds, shutter surfaces must be cleaned from deposits of rust, concrete, oil or other materials. The product is ready to use without any dilution.

Additional Information
Health & Safety

Vetorel XT422 is a mixture of mineral oils and additives that do not pose a threat to human health. The product is not suited for injection.

If swallowed seek medical attention immediately - do not induce vomiting.

For further information consult the Material Safety Data sheet available for this product.


Vetorel XT422 has a shelf flash point, so the flammability risk is low. Do not expose to naked flames or other sources of ignition.

Cleaning and disposal

Spillages of Vetorel XT422 should be absorbed onto sand, earth or vermiculite and transferred to suitable containers. Contaminated areas will become slippery.

The disposal of excess or waste material should be carried out in accordance with local legislation under the guidance of the local waste regulatory authority.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor EG346

Epoxy resin twin cartridge anchoring grout

vetoanchor PG347

Polyester injection and anchoring grout

Vetocure XT425

Water based concrete curing compound

Vetocure XT426

Multi-Purpose Acrylic Resin Curing Compound

Vetocure XT427

Water based acrylic curing compound and primer *

view more
Featured Product
Vetotop UC373

Line Marking Polyurethane Coating for Traffic

As a line marking paint with Vetotop range of products or car park deck coating systems.
General epoxy and polyurethane coated decks
Car park flooring
Concrete surface in factories, warehouses and car parks
Playground and sport flooring
Kerb stones and stair, treads
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Site Map