High strength structural non-shrink self-compacting micro concrete
Vetorep CR521 is a single component polymer modified fibered cementitious structural and non-shrink microconcrete that is ready to use and only requires the addition of water on site. Once mixed the products becomes a self compacting micro-concrete that is applied by pouring into prepared form-work for the repair of demanding structural repair while being compatible with host concrete. Vetorep CR521 is composed of a blend of hydraulic cements, carefully selected and graded aggregates, fibers and special additives to give it its unique properties.
- ASTM C157/157M-08e1
- EN 13062:2003
- EN 1504:2013
Vetorep CR521 supplied in 25 Kg Bag. Consumption - 11.5 Liters Yield.
Vetoprime CP436 supplied in 2kg & 4kg Kit. Consumption -1.18m2/2kg Kit @ 1mm , 2.35m2/4kg Kit @ 1mm
Vetobond AB432 supplied in 4 Liter Can. Consumption - 6-8 m2 / Liter.
Vetobond EB430 supplied in 1 Liter Kit. Consumption - 8 m2 / Liter.
Note: Vetorep CR520 repair area should not exceed 2.5 m2 in single application.
Original sealed kits of Vetorep CR521 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded temperature controlled place <35ºC.
To accept Vetorep CR521, all grit blasted steel reinforcements should be primed within 2 to 4 hours with one or two coats of corrosion inhabitor for steel reinforcement Vetoprime CP436.
Provided that the substrate has been thoroughly soaked with clean water, and is damp on application of product a primer is not normally required. For concrete highly contaminated with soluble salts, it is recommended to use Vetobond EB430, an epoxy bonding agent, which prevents migration of salts such as chloride ions and sulphate to the repair patch, as well as providing enhanced bond for Vetorep CR520 to host concrete.
To ensure proper mixing, a mechanically powered mixer or drill fi tted with suitable paddle should be used. 2.8 to 3 liters of clean water should be added to a clean container.
The powder is then added slowly to the water while mixing continuously with low speed mixer/drill (400 - 600 rpm). Mixing time should be continued for 3 minutes until uniform consistency is obtained.
Placing and Finishing
Vetorep CR521 should be poured in a single continuous operation, within 25 minutes of mixing. The mixed materials should be poured slowly to prevent air entrapment.
As Vetorep CR521 is a cementitious based material, it should be cured in a similar manner to concrete. Curing can be conducted using Vetobond AB432 or by continuous watering and covering with polyethylene sheets.
All tools should be cleaned immediately after application using fresh water. Hardened materials must be cleaned mechanically.
All damaged and weak concrete shall be cut back to reach sound concrete or to a minimum depth of application. Corroded steel reinforcement should be grit blasted to remove all rust traces. Steel loss up to 25% of original section shall be compensated, where loss of section exceeds 25%, steel reinforcement shall be replaced.
Remove all concrete form around exposed steel reinforcements by 25 mm thickness. The perimeters of the repair area should be saw cut to a minimum depth of 10 mm. The prepared area should be cleaned thoroughly by brush and/or compressed air. A water tight form-work should be used to avoid material loss.
Areas to be repaired with Vetorep CR521 should be soaked with clean water for several hours before applying the Vetorep system. All excess water should be removed.
Vetorep CR521 Contains reins which may cause sensitization by skin contact. Avoid contact with skin and eyes and inhalation of vapor. Wear suitable protective clothing, gloves and eye/face protection. Barrier creams provide additional skin protection. Should accidental skin contact occur, remove immediately with a resin removing cream, followed by soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed seek medical attention immediately. Do not induce vomiting.
Vetorep CR521 is non-flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Epoxy resin twin cartridge anchoring grout
Polyester injection and anchoring grout
Water based concrete curing compound
Multi-Purpose Acrylic Resin Curing Compound
Water based acrylic curing compound and primer *
Premixed 8 to 20 mm thick polymer modified cementitious self leveling underlayment.