Tile Adhesives and Grouts

Water resistant grout for swimming pool tile joints.


Grouting of walls and floors joints subjected to varying range of dry or humid conditions.
Pool Grout is specifically designed to be compatible with Saveto Pool Fix product used for laying & fixing tiles.
Suitable for use with both ceramic and marble tiles.
Fast Download
Technical Information
Product Description

Pool Grout is a polymer-modified cementitious tile grout composed of hydraulic binders, selected aggregates, special additives, and polymers. It is supplied as a dry powder in pre-weighed bags ready to use on-site, which requires only addition of clean water to produce easily workable mortar. Pool Grout is ideal for the jointing of Ceramic Tiles, Marbles. Pool Grout is applied in thickness from 2-4 mm for wall tiles and 3-8 mm for floor tiles.

  • Factory controlled pre-blend ensures consistent high quality. 

  • Requires only addition of water on-site at the time of usage.

  • Easy tile installation that enables high Productivity. 

  • Superior workability. 

  • Excellent bonding on variety of ceramic tiles available in the local market.

  • Water & weather resistant.

  • Suitable for internal &  external applications.

  • Suitable for horizontal & vertical surfaces.

Compliance Standard

BS:EN 13888

SASO ISO 13007-3,4 as CG2AW.

Packaging & Coverage

Pool Grout supplied in 25 Kg Bag


  • Wall: 0.3 - 0.5 Kg/LM/3mm Joint
  • Floor: 0.5 - 0.8 Kg/LM/5mm Joint



Shelf Life & Storage

Original sealed container of Pool Grout has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Colored Powder
Application Information
Instructions for use


For the preparation of Pool Grout mortar, pour into a container 8-9 Liters of water for 25 Kg bag of Pool Grout. Add the powder to the water and mix with a low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved. Allow the mixed material to stand for about 10 minutes and remix briefly with no further water to be added. 

It can also be blended manually for small quantity but ensure correct amount of powder to water is maintained. 

If required, add 0.5 Liters of Vetobond AB432 to the mixing water followed by addition of powder.

Mixed material can be used within 1 hour. 

Do not add water to the mix, once the mortar adhesive starts to harden.


Spread the mixed mortar over the tile joints and firmly pressed with rubbing pad covered with sponge rubber spatula.

Pool Grout mortar is spread diagonally across the joints ensuring that the Pool Grout is pressed firmly into the joints. Excess grout that remains on tiles shall be removed with same tool. After initial setting of 20-30 minutes, depending upon the ambient temperature & humidity, clean the tiles and remove all excess material with a wet sponge.

After full drying, clean the tile surfaces with dry cloth or dispensable cotton towels. When washing & drying the tiles, ensure tile joints are not rubbed too deep. Pool Grout must be kept moist for first 2 days after application to ensure good hardened properties are achieved.


Tools and equipment can be cleaned with water immediately after use. Hardened materials will require removal by mechanical means.

Surface Preparation

All excess adhesive tiles that are at the level higher than half of the tile thickness shall be removed.

All the joints should be free from dust, loose materials & traces of foreign materials etc. Neutralize the water absorption of the tiles by applying clean potable water.

Do not leave water pooling in the joints.

Additional Information
Health & Safety

Pool Grout is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.

Pool Grout is non-flammable.


Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.


More Products from this section
Ceramic TILE FIX

Weather resistant cementitious adhesive for ceramic tiles.


Pool FIX

Polymer modified water resistant adhesive for fixing swimming pools, fountains & watertanks tiles.


Porcelain TILE FIX

Polymer modified weather resistant adhesive for porcelain tiles.



High quality ceramic tile adhesive for projects.


Premium FIX

Water resistant premium quality ceramic tile adhesive


view more
Featured Product
Vetonit Base WR

Weather Resistant Premix Cement Coating for Internal Use

Can be applied internally onto walls & ceiling surfaces.
On concrete surfaces that are smooth and also on precast concrete surfaces.
On wall surfaces that are plastered with water resistant plasters, Vetonit Renders and on damp concrete interiors.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map