Jordan
Bahrain Egypt Saudi Arabia UAE
EN
EN
Contact news and events About us Home
PRODUCT RANGE
SYSTEM
Selector REFERENCES DOWNLOAD SECTION
Concrete Grouts, Repairs, & Enhancements
Vetorep CR523

Single component cementitious fairing coat

Uses
Repair of concrete surface blemishes at thickness from feather edge to 3 mm
Unification of concrete surface color
Filling of plaster cracks and concrete hair cracks cosmetically
Filling blow holes up to 10 mm
As a final finish in industrial structures such as parking garages, retaining walls, etc.
Fast Download
Technical Data Sheet
download (*.pdf 0.19Mb)
Method Statement
download (*.pdf 0.22Mb)
MSDS
download (*.pdf 0.87Mb)
Technical Information
Product Description

Vetorep CR523 is a single component polymer modified fibered cementitious fairing coat that is ready to use and only requires the addition of water on site. Once mixed the products becomes a smooth paste that is used to repair surface imperfections up to 3 mm thickness while being compatible with host concrete. Vetorep CR523 is composed of a blend of hydraulic cements, carefully selected and graded aggregates, fibers and special additives to give it its unique properties.

Advantages
  • Easy to use single component product
  • Breathable, compatible to host concrete
  • Self priming, no need for an independent primer for substrate
  • Self curing
  • Chloride free
Compliance Standard
  • BS:EN 1015 - 12 (per BS EN 998)
  • ASTM C348
  • ASTM C109
  • BS:EN 413-2
Packaging & Coverage

Vetorep CR523 supplied in 25 Kg Bag. Consumption - 18 Liters Yield.

Shelf Life & Storage

Original sealed bags of Vetorep CR523 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded temperature controlled place <35ºC.

Application Information
Instructions for use

Mixing

To ensure proper mixing, a mechanically powered mixer or drill fitted with suitable paddle should be used. However for small quantities, Vetorep CR523 can be hand mixed using proper tools and bucket.

Pour 7.5 - 8.5 liter of fresh water to a clean container then add the powder slowly to the water while mixing continuously with low speed mixer/drill (400 - 600 rpm). Mixing time should be continued for 3 minutes until uniform consistency is obtained.

To enhance the scratch resistance of Vetorep 523, the addition of Vetobond PB434 is advisable. Consult your Saveto representative for further information.

Placing and Finishing

Vetorep CR523 can be applied by steel trowel. The mixed mortar can be applied to the prepared substrates at up to 3 mm thicknesses. The applied mortar should be allowed to stiff en before trowelling to a smooth finish..

Curing

Curing is not required for Vetorep CR523 in normal ambient conditions. In the case of harsh weather conditions, such as high wind and temperatures, it is recommended to cure with Vetobond AB432.

Surface Preparation

All surfaces should be clean, sound and uncontaminated prior to the application of Vetorep CR523. The prepared area should be cleaned thoroughly by brush and/or compressed air. The prepared area should be soaked
with water immediately prior to the application of Vetorep CR523.

Additional Information
Health & Safety

Vetorep CR523 Contains reins which may cause sensitization by skin contact. Avoid contact with skin and eyes and inhalation of vapor. Wear suitable protective clothing, gloves and eye/face protection. Barrier creams provide additional skin protection. Should accidental skin contact occur, remove immediately with a resin removing cream, followed by soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed seek medical attention immediately. Do not induce vomiting.

Vetorep CR523 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor EG346

Epoxy resin twin cartridge anchoring grout

vetoanchor PG347

Polyester injection and anchoring grout

Vetocure XT425

Water based concrete curing compound

Vetocure XT426

Multi-Purpose Acrylic Resin Curing Compound

Vetocure XT427

Water based acrylic curing compound and primer *

view more
Featured Product
Vetotherm E1 System Accessories

Vetotherm AFA, Vetotherm ACP,  Vetotherm ABP, & Vetotherm AWP

Uses
Facade anchors are used for fixing Vetotherm EPS (thermal insulation boards) on concrete and light aerated concrete, solid and hollow concrete applicationsand on bricks
Corner Profile reinforcement of window or door corners, edges and jambs
Base Profiles are perfect structural and visual finish and closure of the system
Window reveal creates flexible junction between the contact insulation system and the window or door frame
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map
Home
About us
news and events
Contact
DOWNLOAD SECTION
REFERENCES
Copyright ©2015-2016 Saudi Vetonit Co. Ltd. All Rights Reserved.