High quality gypsum plaster.
Gypsum Plaster is composed of a retarded gypsum, selected aggregates and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce cohesive mix. Gypsum Plaster is a high quality product and provides very smooth surface as underlayment for paints, decorative coatings & wallpapers.
Gypsum Plaster supplied in 35 Kg Bag or Bulk. Consumption : 1.75 Kg /m2 / 1mm thickness
Original sealed bag of Gypsum Plaster has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place.
Mixing
For manual mixing, add to the mixing container 11.5-13 litres of water for each 35 Kg bag of Gypsum Plaster or 450 - 650 Ltr/hr for machine application. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
Leave the mixed material to stand for 5 min and briefly remix without addition of water.
Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when homogenous mix is achieved.
Smooth Concrete Surfaces
Add 0.5 litres of Vetonit Bond 2 to the mixing water and adjust the water requirement accordingly for each 35kg bag. Follow same mixing procedure as above.
Spatter dash SB should be applied prior the application on smooth surfaces if Saveto bond 2 not in use.
Mixed material must be used within 30 minute. Do not add water once the mixed plaster mortar start to stiffen or hardened.
Application
Gypsum Plaster is generally applied in a single coat method. Use directly on block walls & rough surfaces. On smooth concrete surfaces, Spatter Dash SB layer should be applied before or add 0.5 liters of Vetonit Bond2 for each bag of Gypsum Plaster.
Apply mixed material using spray machine or trowel technique to cover the area to desired thickness. Lightweight leveling tools are required in conjunction with trowel to fill in holes.
When the plaster stiffens lightly, treat the surface to a smooth level to eliminate all traces of protrusions and undulations.
Let the plaster set for about 30 min., using wet sponge, wipe the surface to a creamy smooth finish.
Curing
Let the Gypsum Plaster to fully dry itself. Do not use water.
Paints & Coatings can be applied once the plaster has dried out completely, generally after 7 days.
Substrate should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc .Prior to Gypsum Plaster application, wet the entire surfaces with clean potable water and allow to dry prior to Plaster Gypsum application.
Gypsum Plaster is alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.
For further information, please refer to material safety data sheet.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
High quality light weight premixed acoustic plaster
Premixed cementitious masonry grout
Sprayable premixed plaster
Light weight gypsum perlite plaster
Manual Applied Premixed Plaster
Marble chip decorative exterior and interior finishing system